- 您現在的位置：買賣IC網 > PDF目錄376475 > 84072xxx (Electronic Theatre Controls, Inc.) MICROCIRCUIT, DIGITAL, HIGH-SPEED CMOS, OCTAL TRANSPARENT D-TYPE LATCHES WITH THREE STATE OUTPUTS MONOLITIC SILICON PDF資料下載
參數資料
| 型號： | 84072xxx |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | MICROCIRCUIT, DIGITAL, HIGH-SPEED CMOS, OCTAL TRANSPARENT D-TYPE LATCHES WITH THREE STATE OUTPUTS MONOLITIC SILICON |
| 中文描述： | 微電路，數字化，高速的CMOS，八路透明D類鎖存器與三態輸出MONOLITIC硅 |
| 文件頁數： | 5/17頁 |
| 文件大小： | 166K |
| 代理商： | 84072XXX |
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Truth table. The truth table shall be as specified on figure 3.
3.2.4 Logic diagram. The logic diagram shall be as specified on figure 4.
3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified in figure 5.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
case operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space
limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the
RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking
for device class M shall be in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this
drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and
herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or
for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2
herein) involving devices acquired to this drawing is required for any change as defined in MIL-PRF-38535, appendix A.
3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit
group number 36 (see MIL-PRF-38535, appendix A).
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
SIZE
A
84072
REVISION LEVEL
F
SHEET
5
DSCC FORM 2234
APR 97
相關PDF資料 |
PDF描述 |
|---|---|
| 845HN | Sub-Miniature ?1 or 2 pole, 5-12 amps |
| 8480 | Input/Output Modules |
| 8481 | Input/Output Modules |
| 8482 | Input/Output Modules |
| 8483 | Input/Output Modules |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 840730 | 功能描述:FUSE COVER .28 X 1.18 X .5" RoHS:是 類別:過電壓，電流，溫度裝置 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:基座 適用于相關產品:- 其它名稱:UAK-BE/L6 |
| 840730-1 | 制造商:TE Connectivity 功能描述:LGH-1L CERAMIC RECEPT - Bulk |
| 84073012A | 制造商:Texas Instruments 功能描述:Flip Flop D-Type Bus Interface Pos-Edge 1-Element 20-Pin LCCC Tube 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| 84073012C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Hex D-Type Flip-Flop |
| 84073012X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Hex D-Type Flip-Flop |
發布緊急采購，3分鐘左右您將得到回復。