- 您現在的位置：買賣IC網 > PDF目錄8555 > AD5373BSTZ-REEL (Analog Devices Inc)IC DAC 14BIT 32CH SER 64-LQFP PDF資料下載
參數資料
| 型號： | AD5373BSTZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/29頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 14BIT 32CH SER 64-LQFP |
| 標準包裝： | 1 |
| 設置時間： | 20µs |
| 位數： | 14 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 32 |
| 電壓電源： | 模擬和數字，雙 ± |
| 功率耗散（最大）： | 250mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（14x14） |
| 包裝： | 標準包裝 |
| 輸出數目和類型： | 32 電壓，單極；32 電壓，雙極 |
| 采樣率（每秒）： | * |
| 其它名稱： | AD5373BSTZ-REELDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
AD5372/AD5373
Rev. C | Page 18 of 28
The required reference levels can be calculated as follows:
1.
Identify the nominal output range on VOUT.
2.
Identify the maximum offset span and the maximum gain
required on the full output signal range.
3.
Calculate the new maximum output range on VOUT,
including the expected maximum offset and gain errors.
4.
Choose the new required VOUTMAX and VOUTMIN,
keeping the VOUT limits centered on the nominal values.
Note that VDD and VSS must provide sufficient headroom.
5.
Calculate the value of VREF as follows:
VREF = (VOUTMAX – VOUTMIN)/4
Reference Selection Example
If
Nominal output range = 12 V (4 V to +8 V)
Zero-scale error = ±70 mV
Gain error = ±3%, and
SIGGNDx = AGND = 0 V
Then
Gain error = ±3%
=> Maximum positive gain error = 3%
=> Output range including gain error = 12 + 0.03(12) = 12.36 V
Zero-scale error = ±70 mV
=> Maximum offset error span = 2(70 mV) = 0.14 V
=> Output range including gain error and zero-scale error =
12.36 V + 0.14 V = 12.5 V
VREF calculation
Actual output range = 12.5 V, that is, 4.25 V to +8.25 V;
VREF = (8.25 V + 4.25 V)/4 = 3.125 V
If the solution yields an inconvenient reference level, the user
can adopt one of the following approaches:
Use a resistor divider to divide down a convenient, higher
reference level to the required level.
Select a convenient reference level above VREF and modify
the gain and offset registers to digitally downsize the reference.
In this way, the user can use almost any convenient reference
level but can reduce the performance by overcompaction of
the transfer function.
Use a combination of these two approaches.
CALIBRATION
The user can perform a system calibration on the AD5372/
AD5373 to reduce gain and offset errors to below 1 LSB. This
reduction is achieved by calculating new values for the M and C
registers and reprogramming them.
The M and C registers should not be programmed until both
the zero-scale and full-scale errors are calculated.
Reducing Zero-Scale Error
Zero-scale error can be reduced as follows:
1.
Set the output to the lowest possible value.
2.
Measure the actual output voltage and compare it to the
required value. This gives the zero-scale error.
3.
Calculate the number of LSBs equivalent to the error and
add this number to the default value of the C register. Note
that only negative zero-scale error can be reduced.
Reducing Full-Scale Error
Full-scale error can be reduced as follows:
1.
Measure the zero-scale error.
2.
Set the output to the highest possible value.
3.
Measure the actual output voltage and compare it to the
required value. Add this error to the zero-scale error. This
is the span error, which includes the full-scale error.
4.
Calculate the number of LSBs equivalent to the span error
and subtract this number from the default value of the M
register. Note that only positive full-scale error can be
reduced.
AD5372 Calibration Example
This example assumes that a 4 V to +8 V output is required.
The DAC output is set to 4 V but is measured at 4.03 V. This
gives a zero-scale error of 30 mV.
1 LSB = 12 V/65,536 = 183.105 μV
30 mV = 164 LSBs
The full-scale error can now be calculated. The output is set to
8 V and a value of 8.02 V is measured. This gives a full-scale
error of +20 mV and a span error of +20 mV – (–30 mV) =
+50 mV.
50 mV = 273 LSBs
The errors can now be removed as follows:
1.
Add 164 LSBs to the default C register value:
(32,768 + 164) = 32,932
2.
Subtract 273 LSBs from the default M register value:
(65,535 273) = 65,262
3.
Program the M register to 65,262; program the C register
to 32,932.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J5K-MZ-B1 | CONVERTER MOD DC/DC 40V 25W |
| AD568JQ | IC DAC 12BIT HS MONO 35NS 24CDIP |
| VE-J5J-MZ-B1 | CONVERTER MOD DC/DC 36V 25W |
| AD561JD | IC DAC 10BIT 5-15V IN MONO 16DIP |
| VE-J5H-MZ-B1 | CONVERTER MOD DC/DC 52V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5378 | 制造商:AD 制造商全稱:Analog Devices 功能描述:32-Channel, 14-Bit, Parallel and Serial Input, Bipolar Voltage Output DAC |
| AD5378ABC | 功能描述:IC DAC 14BIT 32CHAN 108CSPBGA RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5378ABCZ | 功能描述:IC DAC 14BIT 32CHAN 108CSPBGA RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD5378ABCZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:32-Channel, 14-Bit, Parallel and Serial Input, Bipolar Voltage Output DAC |
| AD5379 | 制造商:AD 制造商全稱:Analog Devices 功能描述:40-Channel, 14-Bit, Parallel and Serial Input, Bipolar Voltage-Output DAC |
發布緊急采購，3分鐘左右您將得到回復。