參數資料
型號: AD5750BCPZ-REEL7
廠商: Analog Devices Inc
文件頁數: 21/36頁
文件大?。?/td> 0K
描述: IC CURR/VOLT OUT DVR 32LFCSP
標準包裝: 1,500
放大器類型: 儀表
電路數: 1
轉換速率: 2 V/µs
電流 - 電源: 5.2mA
電流 - 輸出 / 通道: 24mA
電壓 - 電源,單路/雙路(±): ±10.8 V ~ 26.4 V
工作溫度: -40°C ~ 105°C
安裝類型: 表面貼裝
封裝/外殼: 32-VFQFN 裸露焊盤,CSP
供應商設備封裝: 32-LFCSP-VQ(5x5)
包裝: 帶卷 (TR)
AD5750/AD5750-1
Rev. C | Page 28 of 36
Readback Operation
Readback mode is activated by selecting the correct device address
(A2, A1, A0) and then setting the R/W bit to 1. By default, the
SDO pin is disabled. After having addressed the AD5750/
AD5750-1 for a read operation, setting R/W to 1 enables the
SDO pin and SDO data is clocked out on the 5th rising edge of
SCLK. After the data has been clocked out on SDO, a rising
edge on SYNC disables (tristate) the SDO pin again. Status
register data (see
) and control register data are both
available during the same read cycle.
The status bits comprise four read-only bits. They are used to
notify the user of specific fault conditions that occur, such as
an open circuit or short circuit on the output, overtemperature
error, or an interface error. If any of these fault conditions occur,
a hardware FAULT is also asserted low, which can be used as a
hardware interrupt to the controller.
See the Detailed Description of Features section for a full
explanation of fault conditions.
HARDWARE CONTROL
Hardware control is enabled by connecting the HW SELECT
pin to DVCC. In this mode, the R3, R2, R1, and R0 pins in
conjunction with the RSET pin are used to configure the output
range, as per Table 8.
In hardware mode, there is no status register. The fault condi-
tions (open circuit, short circuit, and overtemperature) are
available on Pin IFAULT, Pin VFAULT, and Pin TEMP. If any
one of these fault conditions are set, then a low is asserted on
the specific fault pin. IFAULT, VFAULT, and TEMP are open-
drain outputs and therefore can be connected together to allow
the user to generate one interrupt to the system controller to
communicate a fault. If hardwired in this way, it is not possible
to isolate which fault occurred in the system.
TRANSFER FUNCTION
The AD5750/AD5750-1 consist of an internal signal
conditioning block that maps the analog input voltage to a
programmed output range. The available analog input ranges
are 0 V to 4.096 V (AD5750) and 0 V to 2.5 V (AD5750-1).
For all ranges, both current and voltage, the AD5750 and
AD5750-1 implement a straight linear mapping function, where
0 V maps to the lower end of the selected range and 4.096 V (or
2.5 V for AD5750-1) maps to the upper end of the selected range.
Table 9. Input Shift Register Contents for a Read Operation—Status Register
MSB
LSB
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
A2
A1
A0
1
0
R3
R2
R1
R0
CLRSEL
OUTEN
RSET
PEC error
OVER TEMP
IOUT fault
VOUT fault
Table 10. Status Bit Options
Bit
Description
PEC Error
This bit is set if there is an interface error detected by CRC-8 error checking. See the Detailed Description of Features section.
OVER TEMP
This bit is set if the AD5750/AD5750-1 core temperature exceeds approximately 150°C.
IOUT Fault
This bit is set if there is an open circuit on the IOUT pin.
VOUT Fault
This bit is set if there is a short circuit on the VOUT pin.
相關PDF資料
PDF描述
9-146309-0-39 CONN HEADR BRKWAY .100 78POS R/A
2035-35-A GAS DISCHARGE TUBE MINI 2 POLE
2035-30-SM GAS DISCHARGE TUBE MINI 2 POLE
FTSH-129-01-L-DH CONN HEADR 58POS DL .05" R/A SMD
2035-30-A GAS DISCHARGE TUBE MINI 2 POLE
相關代理商/技術參數
參數描述
AD5751 制造商:AD 制造商全稱:Analog Devices 功能描述:Industrial Current/Voltage Output Driver
AD5751ACPZ 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源,單路/雙路(±):4.5 V ~ 38 V,±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC(0.154",3.90mm 寬) 供應商設備封裝:8-SOIC 包裝:帶卷 (TR)
AD5751ACPZ 制造商:Analog Devices 功能描述:IC CURRENT/VOLTAGE O/P DRIVER LFCSP-32
AD5751ACPZ-REEL7 功能描述:IC I/V OUTPUT DRIVER 60V 32LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源,單路/雙路(±):7 V ~ 36 V,±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP(0.300",7.62mm) 供應商設備封裝:8-PDIP 包裝:管件
AD5751BCPZ 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源,單路/雙路(±):3 V ~ 32 V,±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR