- 您現在的位置：買賣IC網 > PDF目錄373891 > AD6653 (Analog Devices, Inc.) IF Diversity Receiver PDF資料下載
參數資料
| 型號： | AD6653 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | IF Diversity Receiver |
| 中文描述： | IF分集接收機 |
| 文件頁數： | 51/80頁 |
| 文件大小： | 1998K |
| 代理商： | AD6653 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
AD6653
Bit 5—Peak Detector Output Enable
Bit 5 enables the 13-bit peak measurement as output on the
SPORT.
Bit 4—Threshold Crossing Output Enable
Bit 4 enables the 13-bit threshold measurement as output on the
SPORT.
Bits[3:2]—SPORT SMI SCLK Divide
The values of these bits set the SPORT SMI SCLK divide ratio from
the input clock. A value of 0x01 sets divide-by-2 (default), a value
of 0x10 sets divide-by-4, and a value of 0x11 sets divide-by-8.
Bit 1—SPORT SMI SCLK Sleep
Setting Bit 1 high causes the SMI SCLK to remain low when the
signal monitor block has no data to transfer.
Bit 0—Signal Monitor SPORT Output Enable
When set, Bit 0 enables the signal monitor SPORT output to
begin shifting out the result data from the signal monitor block.
Signal Monitor Control (Register 0x112)
Bit 7—Complex Power Calculation Mode Enable
This mode assumes I data is present on one channel and Q data
is present on the alternate channel. The result reported is the
complex power measured as
Rev. 0 | Page 51 of 80
2
2
Q
I
+
Bits[6:4]—Reserved
Bit 3—Signal Monitor RMS/MS Select
Setting Bit 3 low selects rms power measurement mode. Setting
Bit 3 high selects ms power measurement mode.
Bits[2:1]—Signal Monitor Mode
Bit 2 and Bit 1 set the mode of the signal monitor for data
output to registers at Address 0x116 through Address 0x11B.
Setting these bits to 0x00 selects rms/ms magnitudde output,
setting these bits to 0x01 selects peak detector output, and
setting 0x10 or 0x11 selects threshold crossing output.
Bit 0—Signal Monitor Enable
Setting Bit 0 high enables the signal monitor block.
Signal Monitor Period (Register 0x113 to Register 0x115)
Register 0x115 Bits 7:0—Signal Monitor Period[23:16]
Register 0x114 Bits 7:0—Signal Monitor Period[15:8]
Register 0x113 Bits 7:0—Signal Monitor Period[7:0]
This 24-bit value sets the number of clock cycles over which the
signal monitor performs its operation. The minimum value for
this register is 128 cycles (programmed values less than 128
revert to 128).
Signal Monitor Result Channel A (Register 0x116 to
Register 0x118)
Register 0x118, Bits[7:4]—Reserved
Register 0x118, Bits[3:0]—Signal Monitor Result
Channel A[19:16]
Register 0x117, Bits[7:0]—Signal Monitor Result
Channel A[15:8]
Register 0x116, Bits[7:0]—Signal Monitor Result
Channel A[7:0]
This 20-bit value contains the power value calculated by the
signal monitor block for Channel A. The content is dependent
on the settings in Register 0x112, Bits[2:1].
Signal Monitor Result Channel B (Register 0x119 to
Register 0x11B)
Register 0x11B, Bits[7:4]—Reserved
Register 0x11B, Bits[3:0]—Signal Monitor Result
Channel B[19:16]
Register 0x11A, Bits[7:0]—Signal Monitor Result
Channel B[15:8]
Register 0x119, Bits[7:0]—Signal Monitor Result
Channel B[7:0]
This 20-bit value contains the power value calculated by the
signal monitor block for Channel B. The content is dependent
on the settings in Register 0x112, Bits[2:1].
NCO Control (Register 0x11D)
Bits[7:3]—Reserved
Bit 2—NCO32 Phase Dither Enable
When Bit 2 is set, phase dither in the NCO is enabled. When
Bit 2 is cleared, phase dither is disabled.
Bit 1—NCO32 Amplitude Dither Enable
When Bit 1 is set, amplitude dither in the NCO is enabled.
When Bit 1 is cleared, amplitude dither is disabled.
Bit 0—NCO32 Enable
When Bit 0 is set, this bit enables the 32-bit NCO operating at
the frequency programmed into the NCO frequency register.
When Bit 0 is cleared, the NCO is bypassed and shuts down for
power savings.
相關PDF資料 |
PDF描述 |
|---|---|
| AD6653-125EBZ | IF Diversity Receiver |
| AD6653BCPZ-125 | IF Diversity Receiver |
| AD6653BCPZ-150 | IF Diversity Receiver |
| AD6655BCPZ-1251 | IF Diversity Receiver |
| AD6655 | IF Diversity Receiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD6653-125EBZ | 制造商:Analog Devices 功能描述:Evaluation Board For AD6653 制造商:Analog Devices 功能描述:EVAL BD FOR AD6653 - Bulk 制造商:Analog Devices 功能描述:KIT EVALUATION BOARD AD6653 |
| AD6653-150EBZ | 制造商:Analog Devices 功能描述:EVAL BD FOR AD6653 - Bulk |
| AD6653BCPZ-125 | 制造商:Analog Devices 功能描述:IF DIVERSITY RCVR 64LFCSP EP - Trays 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:IC RECEIVER IF DIVERSITY LFCSP64 |
| AD6653BCPZ-150 | 制造商:Analog Devices 功能描述:IF DIVERSITY RCVR 64LFCSP EP - Trays 制造商:Analog Devices 功能描述:IC RECEIVER IF DIVERSITY LFCSP64 制造商:Analog Devices 功能描述:IC, RECEIVER, IF DIVERSITY, LFCSP64 |
| AD6654 | 制造商:Analog Devices 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。