- 您現在的位置：買賣IC網 > PDF目錄1985 > AD9148BBPZRL (Analog Devices Inc)IC DAC 16BIT SPI/SRL 196BGA PDF資料下載
參數資料
| 型號： | AD9148BBPZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 42/72頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 16BIT SPI/SRL 196BGA |
| 標準包裝： | 1,500 |
| 系列： | TxDAC+® |
| 設置時間： | 20ns |
| 位數： | 16 |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 4 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 2.67W |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 196-LFBGA 裸露焊盤 |
| 供應商設備封裝： | 196-BGA |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 4 電流，單極 |
| 采樣率（每秒）： | 1G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
Data Sheet
AD9148
Rev. B | Page 47 of 72
SAMPLE RATE CLOCK
FPGA
LOW SKEW
CLOCK DRIVER
LOW SKEW
CLOCK DRIVER
MATCHED
LENGTH TRACES
CLK
FRAME
DCI
OUT1
OUT2
SYNC CLOCK
REFCLK/SYNC
CLK
FRAME
DCI
REFCLK/SYNC
MATCHED
LENGTH TRACES
08910-
054
Figure 55. Typical Circuit Diagram for Synchronizing Devices to a System Clock
SYNCHRONIZATION WITH DIRECT CLOCKING
When directly sourcing the DAC sample rate clock to CLK, a
separate REFCLK/SYNC input signal is required for synchronization.
To synchronize devices, the CLK signals and the REFCLK/SYNC
signals must be distributed with low skew to all of the devices
being synchronized. This configuration is shown below in
Data Rate Mode Synchronization
The following procedure outlines the steps required to synchronize
multiple devices in data rate mode. The procedure assumes that
the CLK and REFCLK/SYNC signals are applied to all of the
devices. Each individual device must follow the procedure.
The procedure for data rate synchronization when directly
sourcing the DAC sampling clock follows:
1. Configure for data rate, periodic synchronization by
writing 0xC0 to the sync control register (Register 0x10).
Additional synchronization options are available (see the
2. Poll the sync locked bit (Bit 6, Register 0x12) to verify that
the device is back-end synchronized. A high level on this
bit indicates that the clocks are running with a constant
and known phase relative to the sync signal.
3. Reset the FIFO by strobing the FRAME signal for at least the
time interval needed to load complete data to the four DACs
Resetting the FIFO ensures that the correct data is being
read from the FIFO of each of the devices simultaneously.
This completes the synchronization procedure, and at this
stage, all devices should be synchronized.
To ensure that each of the DACs are updated with the correct data
on the same DACCLK edge, two timing relationships must be
met on each DAC. DCI (and data) must meet the setup and hold
times with respect to the rising edge of CLK, and REFCLK/SYNC
must also meet the setup and hold time with respect to the
rising edge of CLK. When resetting the FIFO, the FRAME
signal must be held high for at least the time interval needed to
load complete data to the four DACs (one DCI period for dual-
port mode and two DCI periods for single-port or byte mode).
When these conditions are met, the outputs of the DACs will be
updated within tSKEW + tOUTDLY nanoseconds of each other. A timing
diagram that illustrates the timing requirements of the input
signals is shown in Figure 56.
CLK(1)
CLK(2)
SYNC(2)
FRAME(2)
DCI(2)
tSKEW
tH_DCI
tSU_DCI
tH_SYNC
tSU_SYNC
08910-
055
Figure 56. Synchronization Signal Timing Requirements in Data Rate Mode,
2× Interpolation
Figure 56 shows the synchronization signal timing with 2×
interpolation, so that fDCI = × fCLK. The REFCLK/SYNC input
is shown equal to the DCI rate. The maximum frequency at which
the device can be resynchronized in data rate mode can be
expressed as
N
DATA
SYNC
f
2
=
for any positive integer, N.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9200ARS | IC ADC CMOS 10BIT 20MSPS 28-SSOP |
| AD9201ARS | IC ADC CMOS 10BIT DUAL 28-SSOP |
| AD9203ARU | IC ADC 10BIT 40MSPS 3V 28-TSSOP |
| AD9204BCPZRL7-80 | IC ADC 10BIT 80MSPS 64LFCSP |
| AD9211BCPZ-200 | IC ADC 10-BIT 200MSPS 56-LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9148BPCZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter |
| AD9148BPCZRL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter |
| AD9148-EBZ | 功能描述:BOARD EVALUATION FOR AD9148 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9148-M5372-EBZ | 功能描述:BOARD EVAL FOR AD9149, ADL5372 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9148-M5375-EBZ | 功能描述:BOARD EVAL FOR AD9149, ADL5375 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
發布緊急采購，3分鐘左右您將得到回復。