參數資料
型號： AD9212-65EBZ
廠商： Analog Devices Inc
文件頁數： 18/56頁
文件大?。?/td> 0K
描述： BOARD EVALUATION FOR AD9212
設計資源： AD9212/22/52 Gerber Files
標準包裝： 1
ADC 的數量： 8
位數： 10
采樣率（每秒）： 65M
數據接口： 串行
輸入范圍： 2 Vpp
在以下條件下的電源（標準）： 100mW @ 65MSPS
工作溫度： -40°C ~ 85°C
已用 IC / 零件： AD9212
已供物品： 板，電源
Data Sheet
AD9212
Rev. E | Page 25 of 56
By asserting the PDWN pin high, the AD9212 is placed into
power-down mode. In this state, the ADC typically dissipates
11 mW. During power-down, the LVDS output drivers are placed
into a high impedance state. The AD9212 returns to normal
operating mode when the PDWN pin is pulled low. This pin is
both 1.8 V and 3.3 V tolerant.
In power-down mode, low power dissipation is achieved by
shutting down the reference, reference buffer, PLL, and biasing
networks. The decoupling capacitors on REFT and REFB are
discharged when entering power-down mode and must be
recharged when returning to normal operation. As a result, the
wake-up time is related to the time spent in the power-down
mode: shorter cycles result in proportionally shorter wake-up
times. With the recommended 0.1 μF and 4.7 μF decoupling
capacitors on REFT and REFB, approximately 1 sec is required
to fully discharge the reference buffer decoupling capacitors,
and approximately 375 μs is required to restore full operation.
There are several other power-down options available when
using the SPI. The user can individually power down each
channel or put the entire device into standby mode. The latter
option allows the user to keep the internal PLL powered when
fast wake-up times (~600 ns) are required. See the Memory
Map section for more details on using these features.
Digital Outputs and Timing
The AD9212 differential outputs conform to the ANSI-644 LVDS
standard by default upon power-up. This can be changed to a low
power, reduced signal option (similar to the IEEE 1596.3 standard)
via the SDIO/ODM pin or the SPI. This LVDS standard can further
reduce the overall power dissipation of the device by approximately
36 mW. See the SDIO/ODM Pin section or Table 16 in the
Memory Map section for more information. The LVDS driver
current is derived on chip and sets the output current at each
output equal to a nominal 3.5 mA. A 100 Ω differential termination
resistor placed at the LVDS receiver inputs results in a nominal
350 mV swing at the receiver.
The AD9212 LVDS outputs facilitate interfacing with LVDS
receivers in custom ASICs and FPGAs for superior switching
performance in noisy environments. Single point-to-point net
topologies are recommended with a 100 Ω termination resistor
placed as close to the receiver as possible. If there is no far-end
receiver termination or there is poor differential trace routing,
timing errors may result. To avoid such timing errors, it is
recommended that the trace length be no longer than 24 inches
and that the differential output traces be kept close together and
at equal lengths. An example of the FCO and data stream when
the AD9212 is used with traces of proper length and position is
shown in Figure 59.
CH1 500mV/DIV = FCO
CH2 500mV/DIV = DCO
CH3 500mV/DIV = DATA
05
96
8-
0
27
5ns/DIV
Figure 59. LVDS Output Timing Example in ANSI-644 Mode (Default),
AD9212-65
An example of the LVDS output using the ANSI-644 standard
(default) data eye and a time interval error (TIE) jitter histogram
with trace lengths less than 24 inches on standard FR-4 material
is shown in Figure 60. Figure 61 shows an example of the trace
length exceeding 24 inches on standard FR-4 material. Notice
that the TIE jitter histogram reflects the decrease of the data eye
opening as the edge deviates from the ideal position. It is the user’s
responsibility to determine if the waveforms meet the timing
budget of the design when the trace lengths exceed 24 inches.
Additional SPI options allow the user to further increase the
internal termination (increasing the current) of all eight outputs
in order to drive longer trace lengths (see Figure 62). Even though
this produces sharper rise and fall times on the data edges and
is less prone to bit errors, the power dissipation of the DRVDD
supply increases when this option is used.
In cases that require increased driver strength to the DCO± and
FCO± outputs because of load mismatch, Register 0x15 allows
the user to increase the drive strength by 2×. To do this, first set the
appropriate bit in Register 0x05. Note that this feature cannot be
used with Bit 4 and Bit 5 in Register 0x15. Bit 4 and Bit 5 take
precedence over this feature. See the Memory Map section for
more details.
相關PDF資料
PDF描述
MAX11040EVKIT+ KIT EVALUATION FOR MAX11040
EBC28DRTI-S13 CONN EDGECARD 56POS .100 EXTEND
EEC44DRTH-S13 CONN EDGECARD 88POS .100 EXTEND
EEC44DREN-S13 CONN EDGECARD 88POS .100 EXTEND
MAX11040KDBEVKIT# KIT EVAL FOR MAX11040 W/FMC CONN
相關代理商/技術參數
參數描述
AD9212ABCPZ-40 功能描述:IC ADC 10BIT SRL 40MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD9212ABCPZ-65 功能描述:IC ADC 10BIT SRL 65MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD9212ABCPZRL7-40 功能描述:IC ADC 10BIT SRL 40MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD9212ABCPZRL7-65 功能描述:IC ADC 10BIT SRL 65MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD9212BCPZ-40 制造商:Analog Devices 功能描述:ADC Octal Pipelined 40Msps 10-bit Serial 64-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述:IC 10BIT ADC 40/65MSPS 1.8V SMD 制造商:Analog Devices 功能描述:IC, 10BIT ADC, 40/65MSPS, 1.8V, SMD
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*