- 您現在的位置：買賣IC網 > PDF目錄17022 > AD9277-50EBZ (Analog Devices Inc)BOARD EVAL FOR AD9277 PDF資料下載
參數資料
| 型號： | AD9277-50EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 35/48頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD9277 |
| 設計資源： | AD9276/77 Eval Brd Gerber Files |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 14 |
| 采樣率（每秒）： | 10M ~ 50M |
| 數據接口： | 串行，SPI? |
| 輸入范圍： | 733 mVpp |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD9277 |
| 已供物品： | 板 |
| 相關產品： | AD9277BSVZ-ND - IC ADC 14BIT LNA/VGA/AAF 100TQFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
AD9277
Rev. 0 | Page 40 of 48
During normal operation, CSB is used to signal to the device
that SPI commands are to be received and processed. When
CSB is brought low, the device processes SCLK and SDIO to
execute instructions. Normally, CSB remains low until the
communication cycle is complete. However, if connected to a
slow device, CSB can be brought high between bytes, allowing
older microcontrollers enough time to transfer data into shift
registers. CSB can be stalled when transferring one, two, or three
bytes of data. When W0 and W1 are set to 11, the device enters
streaming mode and continues to process data, either reading
or writing, until CSB is taken high to end the communication
cycle. This allows complete memory transfers without the need
for additional instructions. Regardless of the mode, if CSB is taken
high in the middle of a byte transfer, the SPI state machine is
reset and the device waits for a new instruction.
In addition to the operation modes, the SPI port can be
configured to operate in different manners. For applications
that do not require a control port, the CSB line can be tied and
held high. This places the remainder of the SPI pins in their
secondary mode (see the AN-877 Application Note). CSB can
also be tied low to enable 2-wire mode. When CSB is tied low,
SCLK and SDIO are the only pins required for communication.
Although the device is synchronized during power-up, caution
must be exercised when using 2-wire mode to ensure that the
serial port remains synchronized with the CSB line. When
operating in 2-wire mode, it is recommended that a 1-, 2-, or
3-byte transfer be used exclusively. Without an active CSB line,
streaming mode can be entered but not exited.
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used to both program the chip and to read
the contents of the on-chip memory. If the instruction is a read-
back operation, performing a readback causes the serial data
input/output (SDIO) pin to change direction from an input to
an output at the appropriate point in the serial frame.
Data can be sent in MSB first mode or LSB first mode. MSB
first mode is the default at power-up and can be changed by
adjusting the configuration register. For more information
about this and other features, see the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI.
HARDWARE INTERFACE
The pins described in Table 16 constitute the physical interface
between the user’s programming device and the serial port of
the AD9277. The SCLK and CSB pins function as inputs when
using the SPI. The SDIO pin is bidirectional, functioning as an
input during write phases and as an output during readback.
If multiple SDIO pins share a common connection, ensure that
pins that can be connected together and the resulting VOH level,
assuming the same load for each AD9277.
08
18
1-
0
71
NUMBER OF SDIO PINS CONNECTED TOGETHER
V
OH
(V
)
1.715
1.720
1.725
1.730
1.735
1.740
1.745
1.750
1.755
1.760
1.765
1.770
1.775
1.780
1.785
1.790
1.795
1.800
030
20
10
40
50
60
70
80
90
100
Figure 77. SDIO Pin Loading
This interface is flexible enough to be controlled by either serial
PROMs or PIC microcontrollers, providing the user with
an alternative method, other than a full SPI controller, for
programming the device (see the AN-812 Application Note).
相關PDF資料 |
PDF描述 |
|---|---|
| RSC15DRXN | CONN EDGECARD 30POS DIP .100 SLD |
| AD9627-125EBZ | IC A/D 12BIT 125MSPS DL EVAL BRD |
| RSC13DRXI | CONN EDGECARD 26POS DIP .100 SLD |
| AD9238BCP-65EBZ | BOARD EVAL WITH AD9238BCP-65 |
| 1210R-100K | COIL .010UH PHENOLIC SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9277BSVZ | 功能描述:IC ADC 14BIT LNA/VGA/AAF 100TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD9278-50EBZ | 功能描述:BOARD EVALUATION FOR AD9278 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| AD9278BBCZ | 功能描述:IC ADC 12BIT 50MSPS 144CSPBGA RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD9279 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Octal LNA/VGA/AAF/ADC and CW I/Q Demodulator |
| AD9279-65EBZ | 功能描述:BOARD EVALUATION FOR AD9279 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。