- 您現在的位置：買賣IC網 > PDF目錄9216 > AD9520-3BCPZ (Analog Devices Inc)IC CLOCK GEN 2GHZ VCO 64LFCSP PDF資料下載
參數資料
| 型號： | AD9520-3BCPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 46/80頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLOCK GEN 2GHZ VCO 64LFCSP |
| 設計資源： | Synchronizing Multiple AD9910 1 GSPS Direct Digital Synthesizers (CN0121) Phase Coherent FSK Modulator (CN0186) |
| 標準包裝： | 1 |
| 類型： | 時鐘發生器，扇出配送 |
| PLL： | 是 |
| 輸入： | CMOS，LVDS，LVPECL |
| 輸出： | CMOS，LVPECL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 2:12，2:24 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 2.25GHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 64-LFCSP-VQ（9x9） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 776 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
AD9520-3
Data Sheet
Rev. A | Page 50 of 80
Hardware Reset via the RESET Pin
RESET, a hard reset (an asynchronous hard reset is executed by
briefly pulling RESET low), restores the chip either to the setting
stored in the EEPROM (the EEPROM pin = 1b) or to the on-chip
setting (the EEPROM pin = 0b). A hard reset also executes
a SYNC operation, bringing the outputs into phase alignment
according to the default settings. When the EEPROM is inactive
(the EEPROM pin = 0b), it takes ~2 s for the outputs to begin
toggling after RESET is issued. When the EEPROM is active
(the EEPROM pin = 1b), it takes ~20 ms for the outputs to toggle
after RESET is brought high.
Soft Reset via the Serial Port
The serial port control register allows for a soft reset by setting
Bit 2 and Bit 5 in Register 0x000. The function of this register is
determined by the state of the EEPROM pin.
When Bit 2 and Bit 5 are set and the EEPROM pin is high, the chip
is restored to the settings saved in the EEPROM. When Bit 2 and
Bit 5 are set and the EEPROM pin is low, the chip is restored to
the on-chip defaults.
Except for the self-clearing bits, Bit 2 and Bit 5, Register 0x000
retains its previous value prior to reset. During the internal reset,
the outputs hold static. However, the self-clearing operation does
not complete until an additional serial port SCLK cycle occurs,
and the AD9520 is held in reset until that happens.
Soft Reset to Settings in EEPROM when EEPROM Pin = 0b
via the Serial Port
If the EEPROM pin is low, the serial port control register allows
the chip to be reset to settings in EEPROM via Register 0xB02[1].
(Bit 1 is self-clearing.) This bit does not have any effect when the
EEPROM pin is high. It takes ~20 ms for the outputs to begin
toggling after the SOFT_EEPROM register is cleared.
POWER-DOWN MODES
Chip Power-Down via PD
The AD9520 can be put into a power-down condition by pulling
the PD pin low. Power-down turns off most of the functions and
currents inside the AD9520. The chip remains in this power-down
state until PD is brought back to logic high. When taken out of
power-down mode, the AD9520 returns to the settings
programmed into its registers prior to the power-down, unless
the registers are changed by new programming while the PD
pin is held low.
Powering down the chip shuts down the currents on the chip,
except for the bias current necessary to maintain the LVPECL
outputs in a safe shutdown mode. The LVPECL bias currents are
needed to protect the LVPECL output circuitry from damage that
can be caused by certain termination and load configurations
when tristated. Because this is not a complete power-down, it
can be called sleep mode. The AD9520 contains special circuitry to
prevent runt pulses on the outputs when the chip is entering or
exiting sleep mode.
When the AD9520 is in a PD power-down, the chip is in the
following state:
The PLL is off (asynchronous power-down).
The VCO is off.
The CLK input buffer is off, but the CLK input dc bias
circuit is on.
In differential mode, the reference input buffer is off, but
the dc bias circuit is still on.
In singled-ended mode, the reference input buffer is off,
and the dc bias circuit is off.
All dividers are off.
All CMOS outputs are tristated.
All LVPECL outputs are in safe off mode.
The serial control port is active, and the chip responds to
commands.
PLL Power-Down
The PLL section of the AD9520 can be selectively powered
down. There are two PLL power-down modes set by
Register 0x010[1:0]: asynchronous and synchronous.
In asynchronous power-down mode, the device powers down as
soon as the registers are updated. In synchronous power-down
mode, the PLL power-down is gated by the charge pump to
prevent unwanted frequency jumps. The device goes into power-
down on the occurrence of the next charge pump event after the
registers are updated.
Distribution Power-Down
The distribution section can be powered down by writing
Register 0x230[1] = 1b, which turns off the bias to the distribution
section. If the LVPECL power-down mode is in normal operation
(Register 0x230[1] = 0b), it is possible for a low impedance load
on that LVPECL output to draw significant current during this
power-down. If the LVPECL power-down mode is set to 1b, the
LVPECL output is not protected from reverse bias and can be
damaged under certain termination conditions.
Individual Clock Output Power-Down
Any of the clock distribution outputs can be powered down
into safe power-down mode by individually writing to the
appropriate registers. The register map details the individual
power-down settings for each output. These settings are found
in Bit 0 of Register 0x0F0 to Register 0x0FB.
Individual Clock Channel Power-Down
Any of the clock distribution channels can be powered down
individually by writing to the appropriate registers. Powering
down a clock channel is similar to powering down an individual
driver, but it saves more power because the dividers are also
powered down. Powering down a clock channel also automatically
powers down the drivers connected to it. The register map
details the individual power-down settings for each output
channel. These settings are found in Bit 2 of Register 0x192,
Register 0x195, Register 0x198, and Register 0x19B.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B42-MV | CONVERTER MOD DC/DC 15V 150W |
| VE-213-MY-F2 | CONVERTER MOD DC/DC 24V 50W |
| AD9516-1BCPZ | IC CLOCK GEN 2.5GHZ VCO 64-LFCSP |
| X9C303V8IZ | IC XDCP 100-TAP 32K EE 8-TSSOP |
| VE-B41-MV | CONVERTER MOD DC/DC 12V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9520-3BCPZ-REEL7 | 功能描述:IC CLOCK GEN 2GHZ VCO 64LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR) |
| AD9520-4 | 制造商:AD 制造商全稱:Analog Devices 功能描述:12 LVPECL/24 CMOS Output Clock Generator with Integrated 1.6 GHz VCO |
| AD9520-4/PCBZ | 功能描述:BOARD EVAL FOR AD9520-4 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| AD9520-4BCPZ | 功能描述:IC CLOCK GEN 1.6GHZ VCO 64LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 頻率合成器 PLL:是 輸入:晶體 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:1 差分 - 輸入:輸出:無/無 頻率 - 最大:1GHz 除法器/乘法器:是/無 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-LSSOP（0.175"，4.40mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:NJW1504V-TE1-NDNJW1504V-TE1TR |
| AD9520-4BCPZ-REEL7 | 功能描述:IC CLOCK GEN 1.6GHZ VCO 64LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。