參數資料
型號： AD9520-3BCPZ
廠商： Analog Devices Inc
文件頁數： 47/80頁
文件大?。?/td> 0K
描述： IC CLOCK GEN 2GHZ VCO 64LFCSP
設計資源： Synchronizing Multiple AD9910 1 GSPS Direct Digital Synthesizers (CN0121)
Phase Coherent FSK Modulator (CN0186)
標準包裝： 1
類型： 時鐘發生器，扇出配送
PLL： 是
輸入： CMOS，LVDS，LVPECL
輸出： CMOS，LVPECL
電路數： 1
比率 - 輸入:輸出： 2:12，2:24
差分 - 輸入:輸出： 是/是
頻率 - 最大： 2.25GHz
除法器/乘法器： 是/無
電源電壓： 3.135 V ~ 3.465 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 64-VFQFN 裸露焊盤，CSP
供應商設備封裝： 64-LFCSP-VQ（9x9）
包裝： 托盤
產品目錄頁面： 776 (CN2011-ZH PDF)
Data Sheet
AD9520-3
Rev. A | Page 51 of 80
SERIAL CONTROL PORT
The AD9520 serial control port is a flexible, synchronous serial
communications port that allows an easy interface with many
industry-standard microcontrollers and microprocessors. The
AD9520 serial control port is compatible with most synchronous
transfer formats, including Philips IC, Motorola SPI, and
Intel SSR protocols. The AD9520 IC implementation deviates
from the classic IC specification on two specifications, and
these deviations are documented in Table 14. The serial control
port allows read/write access to all registers that configure the
SPI/IC PORT SELECTION
The AD9520 has two serial interfaces, SPI and IC. Users can
select either SPI or IC depending on the states of the three- level
(high, open, low) logic input pins, SP1 and SP0. When both SP1
and SP0 are high, the SPI interface is active. Otherwise, IC is active
with eight different IC slave address (seven bits wide) settings
(see Table 41). The four MSBs of the slave address are hardware
coded as 1011b; the three LSBs are programmed by SP1 and SP0.
Table 41. Serial Port Mode Selection
SP1
SP0
Address
Low
IC, 1011000b
Low
Open
IC, 1011001b
Low
High
IC, 1011010b
Open
Low
IC, 1011011b
Open
IC, 1011100b
Open
High
IC, 1011101b
High
Low
IC, 1011110b
High
Open
IC, 1011111b
High
SPI
IC SERIAL PORT OPERATION
The AD9520 IC port is based on the IC fast mode standard.
The AD9520 supports both IC protocols: standard mode
(100 kHz) and fast mode (400 kHz).
The AD9520 IC port has a 2-wire interface consisting of a serial
data line (SDA) and a serial clock line (SCL). In an IC bus system,
the AD9520 is connected to the serial bus (data bus SDA and clock
bus SCL) as a slave device, meaning that no clock is generated by
the AD9520. The AD9520 uses direct 16-bit (two bytes) memory
addressing instead of traditional 8-bit (one byte) memory
addressing.
I2C Bus Characteristics
Table 42. I2C Bus Definitions
Abbreviation
Definition
S
Start
Sr
Repeated start
P
Stop
A
Acknowledge
A
No acknowledge
W
Write
R
Read
One pulse on the SCL clock line is generated for each data bit
transferred.
The data on the SDA line must not change during the high period
of the clock. The state of the data line can change only when the
clock on the SCL line is low.
SDA
SCL
DATA LINE
STABLE;
DATA VALID
CHANGE
OF DATA
ALLOWED
07216-
160
Figure 56. Valid Bit Transfer
A start condition is a transition from high to low on the SDA
line while SCL is high. The start condition is always generated
by the master to initialize the data transfer.
A stop condition is a transition from low to high on the SDA
line while SCL is high. The stop condition is always generated
by the master to end the data transfer.
START
CONDITION
S
STOP
CONDITION
P
SDA
SCL
07216-
161
Figure 57. Start and Stop Conditions
A byte on the SDA line is always eight bits long. An acknowledge
bit must follow every byte. Bytes are sent MSB first.
The acknowledge bit is the ninth bit attached to any 8-bit data
byte. An acknowledge bit is always generated by the receiving
device (receiver) to inform the transmitter that the byte has
been received. It is accomplished by pulling the SDA line low
during the ninth clock pulse after each 8-bit data byte.
The no acknowledge bit is the ninth bit attached to any 8-bit
data byte. A no acknowledge bit is always generated by the
receiving device (receiver) to inform the transmitter that the
byte has not been received. It is accomplished by leaving the SDA
line high during the ninth clock pulse after each 8-bit data byte.
相關PDF資料
PDF描述
VE-B42-MV CONVERTER MOD DC/DC 15V 150W
VE-213-MY-F2 CONVERTER MOD DC/DC 24V 50W
AD9516-1BCPZ IC CLOCK GEN 2.5GHZ VCO 64-LFCSP
X9C303V8IZ IC XDCP 100-TAP 32K EE 8-TSSOP
VE-B41-MV CONVERTER MOD DC/DC 12V 150W
相關代理商/技術參數
參數描述
AD9520-3BCPZ-REEL7 功能描述:IC CLOCK GEN 2GHZ VCO 64LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR)
AD9520-4 制造商:AD 制造商全稱:Analog Devices 功能描述:12 LVPECL/24 CMOS Output Clock Generator with Integrated 1.6 GHz VCO
AD9520-4/PCBZ 功能描述:BOARD EVAL FOR AD9520-4 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源
AD9520-4BCPZ 功能描述:IC CLOCK GEN 1.6GHZ VCO 64LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 頻率合成器 PLL:是 輸入:晶體 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:1 差分 - 輸入:輸出:無/無 頻率 - 最大:1GHz 除法器/乘法器:是/無 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-LSSOP（0.175"，4.40mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:NJW1504V-TE1-NDNJW1504V-TE1TR
AD9520-4BCPZ-REEL7 功能描述:IC CLOCK GEN 1.6GHZ VCO 64LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*