參數資料
型號： AD9613-170EBZ
廠商： Analog Devices Inc
文件頁數： 20/36頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD9613-170
標準包裝： 1
ADC 的數量： 2
位數： 12
采樣率（每秒）： 170M
數據接口： 串行，SPI?
輸入范圍： 1.75 Vpp
在以下條件下的電源（標準）： 670mW @ 170MSPS
工作溫度： -40°C ~ 85°C
已用 IC / 零件： AD9613
已供物品： 板
Data Sheet
AD9613
Rev. C | Page 27 of 36
POWER DISSIPATION AND STANDBY MODE
As shown in Figure 57, the power dissipated by the AD9613 is
proportional to its sample rate. The data in Figure 57 was taken
using the same operating conditions as those used for the Typical
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.5
0.4
0.3
0.2
0.1
0
40
60
80
100
120
140
160
180
200
220
240
ENCODE FREQUENCY (MSPS)
TOTA
L
P
OWE
R
(
W)
S
UP
P
L
Y
CURRE
NT
(
A)
09637-
061
TOTAL POWER
IAVDD
IDRVDD
Figure 57. AD9613-250 Power and Current vs. Sample Rate
By asserting PDWN (either through the SPI port or by asserting
the PDWN pin high), the AD9613 is placed in power-down mode.
In this state, the ADC typically dissipates 10 mW. During power-
down, the output drivers are placed in a high impedance state.
Asserting the PDWN pin low returns the AD9613 to its normal
operating mode. Note that PDWN is referenced to the digital
output driver supply (DRVDD) and should not exceed that
supply voltage.
Low power dissipation in power-down mode is achieved by
shutting down the reference, reference buffer, biasing networks,
and clock. Internal capacitors are discharged when entering
power-down mode and then must be recharged when returning
to normal operation. As a result, wake-up time is related to the
time spent in power-down mode, and shorter power-down
cycles result in proportionally shorter wake-up times.
When using the SPI port interface, the user can place the ADC
in power-down mode or standby mode. Standby mode allows
the user to keep the internal reference circuitry powered when
faster wake-up times are required. See the Memory Map Register
Description section and the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI, for additional details.
DIGITAL OUTPUTS
The AD9613 output drivers can be configured for either ANSI
LVDS or reduced drive LVDS using a 1.8 V DRVDD supply.
As detailed in Application Note AN-877, Interfacing to High
Speed ADCs via SPI, the data format can be selected for offset
binary, twos complement, or gray code when using the SPI
control.
Digital Output Enable Function (OEB)
The AD9613 has a flexible three-state ability for the digital output
pins. The three-state mode is enabled using the OEB pin or
through the SPI interface. If the OEB pin is low, the output data
drivers are enabled. If the OEB pin is high, the output data drivers
are placed in a high impedance state. This OEB function is not
intended for rapid access to the data bus. Note that OEB is
referenced to the digital output driver supply (DRVDD) and
should not exceed that supply voltage.
When using the SPI interface, the data outputs of each channel
can be independently three-stated by using the output enable bar
bit (Bit 4) in Register 0x14. Because the output data is interleaved,
if only one of the two channels is disabled, the output data of
the remaining channel is repeated in both the rising and falling
output clock cycles.
Timing
The AD9613 provides latched data with a pipeline delay of 10 input
sample clock cycles. Data outputs are available one propagation
delay (tPD) after the rising edge of the clock signal.
Minimize the length of the output data lines and loads placed
on them to reduce transients within the AD9613. These
transients can degrade converter dynamic performance.
The lowest typical conversion rate of the AD9613 is 40 MSPS. At
clock rates below 40 MSPS, dynamic performance can degrade.
Data Clock Output (DCO)
The AD9613 also provides data clock output (DCO) intended for
capturing the data in an external register. Figure 2 shows a timing
diagram of the AD9613 output modes.
ADC OVERRANGE (OR)
The ADC overrange indicator is asserted when an overrange is
detected on the input of the ADC. The overrange condition is
determined at the output of the ADC pipeline and, therefore, is
subject to a latency of 10 ADC clock. An overrange at the input is
indicated by this bit 10 clock cycles after it.
Table 11. Output Data Format
Input (V)
VIN+ VIN,
Input Span = 1.75 V p-p (V)
Offset Binary Output Mode
Twos Complement Mode (Default)
OR
VIN+ VIN–
Less than –0.875
0000 0000 0000
1000 0000 0000
1
VIN+ VIN–
–0.875
0000 0000 0000
1000 0000 0000
0
VIN+ VIN–
0
1000 0000 0000
0000 0000 0000
0
VIN+ VIN–
+0.875
1111 1111 1111
0111 1111 1111
0
VIN+ VIN–
Greater than +0.875
1111 1111 1111
0111 1111 1111
1
相關PDF資料
PDF描述
GCM15DRTF-S13 CONN EDGECARD 30POS .156 EXTEND
GCM15DRKF-S13 CONN EDGECARD 30POS .156 EXTEND
ECM18DRYN-S13 CONN EDGECARD 36POS .156 EXTEND
380LX103M025H032 CAP ALUM 10000UF 25V 20% SNAP
VI-JWX-EY CONVERTER MOD DC/DC 5.2V 50W
相關代理商/技術參數
參數描述
AD9613-210EBZ 功能描述:數據轉換 IC 開發工具 0Msps Dual ADC RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
AD9613-250EBZ 功能描述:數據轉換 IC 開發工具 12 Bit 250Msps Dual ADC RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
AD9613BCPZ-170 功能描述:IC ADC 12BIT SRL 170MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD9613BCPZ-210 功能描述:模數轉換器 - ADC 12 Bit 210Msps Dual ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體:
AD9613BCPZ-250 制造商:Analog Devices 功能描述:ADC Dual Pipelined 250Msps 12-bit Parallel/LVDS 64-Pin LFCSP EP Tray 制造商:Analog Devices 功能描述:12 BIT 250MSPS DUAL ADC - Trays 制造商:Analog Devices 功能描述:IC ADC 12BIT SRL 250MSPS 64LFCSP 制造商:Analog Devices 功能描述:IC ADC 12BIT 250MSPS 3-Wir 制造商:Analog Devices 功能描述:ADC 12BIT SRL 250MSPS 64LFCSP 制造商:Analog Devices Inc. 功能描述:Analog to Digital Converters - ADC 12 Bit 250Msps Dual ADC 制造商:Analog Devices 功能描述:IC, ADC, 12BIT, 250MSPS, 3-Wire, Serial, LFCSP-64; Resolution (Bits):12bit; Sampling Rate:250MSPS; Supply Voltage Type:Single; Supply Voltage Min:1.7V; Supply Voltage Max:1.9V; Supply Current:252mA; Digital IC Case Style:LFCSP ;RoHS Compliant: Yes 制造商:Analog Devices 功能描述:CONVERTER - ADC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*