- 您現在的位置：買賣IC網 > PDF目錄10064 > AD9613BCPZRL7-170 (Analog Devices Inc)IC ADC 12BIT SRL 170MSPS 64LFCSP PDF資料下載
參數資料
| 型號： | AD9613BCPZRL7-170 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 25/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT SRL 170MSPS 64LFCSP |
| 標準包裝： | 750 |
| 位數： | 12 |
| 采樣率（每秒）： | 170M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 738mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 64-LFCSP-VQ（9x9） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Data Sheet
AD9613
Rev. C | Page 31 of 36
MEMORY MAP
READING THE MEMORY MAP REGISTER TABLE
Each row in the memory map register table has eight bit locations.
The memory map is roughly divided into four sections: the chip
configuration registers (Address 0x00 to Address 0x02); the
channel index and transfer registers (Address 0x05 and
Address 0xFF); and the ADC functions registers, including
setup, control, and test (Address 0x08 to Address 0x3A).
The memory map register table (see Table 14) documents the
default hexadecimal value for each hexadecimal address shown.
The column with the heading Bit 7 (MSB) is the start of the default
hexadecimal value given. For example, Address 0x14, the output
mode register, has a hexadecimal default value of 0x05. This
means that Bit 0 = 1 and Bit 2 = 1, and the remaining bits are
0s. This setting is the default output format value, which is twos
complement. For more information on this function and others,
see the AN-877 Application Note, Interfacing to High Speed ADCs
via SPI. This document details the functions controlled by
Register 0x00 to Register 0x20. The remaining register, Register
0x3A, is documented in the Memory Map Register Description
section.
Open and Reserved Locations
All address and bit locations that are not included in Table 14
are not currently supported for this device. Unused bits of a
valid address location should be written with 0s. Writing to these
locations is required only when part of an address location is
open (for example, Address 0x18). If the entire address location
is open (for example, Address 0x13), this address location should
not be written.
Default Values
After the AD9613 is reset, critical registers are loaded with
default values. The default values for the registers are given in
the memory map register table (see Table 14).
Logic Levels
An explanation of logic level terminology follows:
“Bit is set” is synonymous with “bit is set to Logic 1” or
“writing Logic 1 for the bit.”
“Clear a bit” is synonymous with “bit is set to Logic 0” or
“writing Logic 0 for the bit.”
Transfer Register Map
Address 0x08 to Address 0x20 and Address 0x3A are shadowed.
Writes to these addresses do not affect part operation until a
transfer command is issued by writing 0x01 to Address 0xFF,
setting the transfer bit. This allows these registers to be updated
internally and simultaneously when the transfer bit is set. The
internal update takes place when the transfer bit is set and the
bit autoclears.
Channel Specific Registers
Some channel setup functions, such as the signal monitor
thresholds, can be programmed to a different value for each
channel. In these cases, channel address locations are internally
duplicated for each channel. These registers and bits are designated
in Table 14 as local. These local registers and bits can be accessed
by setting the appropriate Channel A or Channel B bits in Register
0x05. If both bits are set, the subsequent write affects the registers
of both channels. In a read cycle, only Channel A or Channel B
should be set to read one of the two registers. If both bits are set
during an SPI read cycle, the part returns the value for Channel A.
Registers and bits designated as global in Table 14 affect the entire
part and the channel features for which independent settings are
not allowed between channels. The settings in Register 0x05 do
not affect the global registers and bits.
相關PDF資料 |
PDF描述 |
|---|---|
| IDT72225LB25PFI | IC FIFO 1024X18 SYNC 25NS 64TQFP |
| LT1138ACSW#TR | IC TXRX 5V RS232 LP CAPS 28SOIC |
| IDT72V241L20J | IC FIFO SYNC 4KX9 20NS 32PLCC |
| LT1130ACSW#TRPBF | IC 5DRV/5RCV RS232 5V 28-SOIC |
| IDT72V231L15J | IC FIFO SYNC 2048X9 15NS 32-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9613BCPZRL7-210 | 功能描述:模數轉換器 - ADC 12 Bit 210Msps Dual ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9613BCPZRL7-250 | 功能描述:模數轉換器 - ADC 12 Bit 250Msps Dual ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9615BH | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD9615TH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current-Feedback Operational Amplifier |
| AD9617 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Distortion, Precision, Wide Bandwidth Op Amp |
發布緊急采購，3分鐘左右您將得到回復。