參數資料
型號： AD9627-125EBZ
廠商： Analog Devices Inc
文件頁數： 30/76頁
文件大小： 0K
描述： IC A/D 12BIT 125MSPS DL EVAL BRD
標準包裝： 1
ADC 的數量： 2
位數： 12
采樣率（每秒）： 125M
數據接口： 串行
輸入范圍： 2 Vpp
在以下條件下的電源（標準）： 900mW @ 125MSPS
工作溫度： -40°C ~ 85°C
已用 IC / 零件： AD9627
已供物品： 板，電源
AD9627
Rev. B | Page 36 of 76
SIGNAL MONITOR
The signal monitor block provides additional information
about the signal being digitized by the ADC. The signal monitor
computes the rms input magnitude, the peak magnitude,
and/or the number of samples by which the magnitude exceeds
a particular threshold. Together, these functions can be used to
gain insight into the signal characteristics and to estimate the
peak/average ratio or even the shape of the complementary
cumulative distribution function (CCDF) curve of the input signal.
This information can be used to drive an AGC loop to optimize
the range of the ADC in the presence of real-world signals.
The signal monitor result values can be obtained from the part by
reading back internal registers at Address 0x116 to Address 0x11B,
using the SPI port or the signal monitor SPORT output. The output
contents of the SPI-accessible signal monitor registers are set via
the two signal monitor mode bits of the signal monitor control
register. Both ADC channels must be configured for the same
signal monitor mode. Separate SPI-accessible, 20-bit signal monitor
result (SMR) registers are provided for each ADC channel. Any
combination of the signal monitor functions can also be output
to the user via the serial SPORT interface. These outputs are
enabled using the peak detector output enable, the rms magnitude
output enable, and the threshold crossing output enable bits in
the signal monitor SPORT control register.
For each signal monitor measurement, a programmable signal
monitor period register (SMPR) controls the duration of the
measurement. This time period is programmed as the number of
input clock cycles in a 24-bit signal monitor period register
located at Address 0x113, Address 0x114, and Address 0x115.
This register can be programmed with a period from 128 samples
to 16.78 (224) million samples.
Because the dc offset of the ADC can be significantly larger
than the signal of interest (affecting the results from the signal
monitor), a dc correction circuit is included as part of the signal
monitor block to null the dc offset before measuring the power.
PEAK DETECTOR MODE
The magnitude of the input port signal is monitored over a
programmable time period (determined by SMPR) to give the
peak value detected. This function is enabled by programming
a Logic 1 in the signal monitor mode bits of the signal monitor
control register or by setting the peak detector output enable bit
in the signal monitor SPORT control register. The 24-bit SMPR
must be programmed before activating this mode.
After enabling this mode, the value in the SMPR is loaded into
a monitor period timer and the countdown is started. The magni-
tude of the input signal is compared with the value in the internal
peak level holding register (not accessible to the user), and the
greater of the two is updated as the current peak level. The initial
value of the peak level holding register is set to the current ADC
input signal magnitude. This comparison continues until the
monitor period timer reaches a count of 1.
When the monitor period timer reaches a count of 1, the 13-bit
peak level value is transferred to the signal monitor holding register
(not accessible to the user), which can be read through the SPI port
or output through the SPORT serial interface. The monitor period
timer is reloaded with the value in the SMPR, and the countdown is
restarted. In addition, the magnitude of the first input sample is
updated in the peak level holding register, and the comparison and
update procedure, as explained previously, continues.
Figure 68 is a block diagram of the peak detector logic. The SMR
register contains the absolute magnitude of the peak detected by
the peak detector logic.
SIGNAL MONITOR
HOLDING
REGISTER (SMR)
MAGNITUDE
STORAGE
REGISTER
COMPARE
A>B
TO
MEMORY
MAP/SPORT
FROM
MEMORY
MAP
FROM
INPUT
PORTS
LOAD
CLEAR
LOAD
IS COUNT = 1?
DOWN
COUNTER
SIGNAL MONITOR
PERIOD REGISTER
06
57
1-
06
8
Figure 68. ADC Input Peak Detector Block Diagram
RMS/MS MAGNITUDE MODE
In this mode, the root-mean-square (rms) or mean-square (ms)
magnitude of the input port signal is integrated (by adding an
accumulator) over a programmable time period (determined by
SMPR) to give the rms or ms magnitude of the input signal.
This mode is set by programming Logic 0 in the signal monitor
mode bits of the signal monitor control register or by setting the
rms magnitude output enable bit in the signal monitor SPORT
control register. The 24-bit SMPR, representing the period over
which integration is performed, must be programmed before
activating this mode.
After enabling the rms/ms magnitude mode, the value in the SMPR
is loaded into a monitor period timer, and the countdown is started
immediately. Each input sample is converted to floating-point
format and squared. It is then converted to 11-bit, fixed-point
format and added to the contents of the 24-bit accumulator.
The integration continues until the monitor period timer reaches
a count of 1.
When the monitor period timer reaches a count of 1, the square
root of the value in the accumulator is taken and transferred,
after some formatting, to the signal monitor holding register, which
can be read through the SPI port or output through the SPORT
serial port. The monitor period timer is reloaded with the value
in the SMPR, and the countdown is restarted. In addition, the
first input sample signal power is updated in the accumulator,
and the accumulation continues with the subsequent input
samples.
相關PDF資料
PDF描述
RSC13DRXI CONN EDGECARD 26POS DIP .100 SLD
AD9238BCP-65EBZ BOARD EVAL WITH AD9238BCP-65
1210R-100K COIL .010UH PHENOLIC SMD
RSC15DRXH CONN EDGECARD 30POS DIP .100 SLD
AD9216-80PCBZ BOARD EVAL FOR AD9216 80MSPS
相關代理商/技術參數
參數描述
AD9627-150EBZ 功能描述:數據轉換 IC 開發工具 12Bit 150 Msps Dual 1.8V PB Free ADC RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
AD9627ABCPZ-105 功能描述:IC ADC 12BIT 105MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD9627ABCPZ11-105 功能描述:IC ADC 11BIT 105MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD9627ABCPZ11-150 功能描述:IC ADC 11BIT 150MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD9627ABCPZ-125 功能描述:IC ADC 12BIT 1255MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*