參數資料
型號： ADF4158CCPZ-RL7
廠商： Analog Devices Inc
文件頁數： 27/36頁
文件大?。?/td> 0K
描述： IC FRACTION N FREQ SYNT 24LFCSP
標準包裝： 1,500
類型： 分?jǐn)?shù) N 合成器（RF）
PLL： 是
輸入： CMOS，TTL
輸出： 時鐘
電路數： 1
比率 - 輸入:輸出： 2:1
差分 - 輸入:輸出： 是/無
頻率 - 最大： 6.1GHz
除法器/乘法器： 是/是
電源電壓： 2.7 V ~ 3.3 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 24-WFQFN 裸露焊盤，CSP
供應商設備封裝： 24-LFCSP-WQ（4x4）
包裝： 帶卷 (TR)
Data Sheet
ADF4158
Rev. G | Page 33 of 36
SPUR MECHANISMS
The fractional interpolator in the ADF4158 is a third-order Σ-Δ
modulator (SDM) with a 25-bit fixed modulus (MOD). The SDM
is clocked at the PFD reference rate (fPFD) that allows PLL output
frequencies to be synthesized at a channel step resolution of fPFD/
MOD. The various spur mechanisms possible with fractional-N
synthesizers and how they affect the ADF4158 are discussed in
this section.
Fractional Spurs
In most fractional synthesizers, fractional spurs can appear at
the set channel spacing of the synthesizer. In the ADF4158,
these spurs do not appear. The high value of the fixed modulus
in the ADF4158 makes the SDM quantization error spectrum
look like broadband noise, effectively spreading the fractional
spurs into noise.
Integer Boundary Spurs
Interactions between the RF VCO frequency and the PFD
frequency can lead to spurs known as integer boundary spurs.
When these frequencies are not integer related (which is the
purpose of the fractional-N synthesizer), spur sidebands appear on
the VCO output spectrum at an offset frequency that corresponds
to the beat note or difference frequency between an integer
multiple of the PFD and the VCO frequency.
These spurs are named integer boundary spurs because they are
more noticeable on channels close to integer multiples of the PFD
where the difference frequency can be inside the loop bandwidth.
These spurs are attenuated by the loop filter on channels far
from integer multiples of the PFD.
Reference Spurs
Reference spurs are generally not a problem in fractional-N
synthesizers because the reference offset is far outside the loop
bandwidth. However, any reference feedthrough mechanism that
bypasses the loop can cause a problem. One such mechanism is
the feedthrough of low levels of on-chip reference switching noise
out through the RFIN pins back to the VCO, resulting in reference
spur levels as high as 90 dBc. Take care in the printed circuit
board (PCB) layout to ensure that the VCO is well separated
from the input reference to avoid a possible feedthrough path
on the board.
LOW FREQUENCY APPLICATIONS
The specification on the RF input is 0.5 GHz minimum; however,
RF frequencies lower than this can be used if the minimum slew
rate specification of 400 V/s is met. An appropriate LVDS driver
can be used to square up the RF signal before it is fed back to the
ADF4158 RF input. The FIN1001 from Fairchild Semiconductor
is one such LVDS driver.
FILTER DESIGN—ADIsimPLL
A filter design and analysis program is available to help the user
implement PLL design. Visit www.analog.com/pll for a free
download of the ADIsimPLL software. This software designs,
simulates, and analyzes the entire PLL frequency domain and time
domain response. Various passive and active filter architectures
are allowed.
PCB DESIGN GUIDELINES FOR THE CHIP SCALE
PACKAGE
The lands on the chip scale package (CP-24) are rectangular.
The PCB pad for these should be 0.1 mm longer than the package
land length and 0.05 mm wider than the package land width.
Center the land on the pad. This ensures that the solder joint size
is maximized.
The bottom of the chip scale package has a central thermal pad.
The thermal pad on the PCB should be at least as large as this
exposed pad. On the PCB, there should be a clearance of at least
0.25 mm between the thermal pad and the inner edges of the
pad pattern. This ensures that shorting is avoided.
Thermal vias can be used on the PCB thermal pad to improve
the thermal performance of the package. If vias are used, they
should be incorporated into the thermal pad at 1.2 mm pitch
grid. The via diameter should be between 0.3 mm and 0.33 mm,
and the via barrel should be plated with 1 ounce of copper to
plug the via. Connect the PCB thermal pad to AGND.
相關PDF資料
PDF描述
X9409WV24-2.7T1 IC XDCP QUAD 64-TAP 10K 24-TSSOP
X9409WS24T1 IC XDCP QUAD 64-TAP 10K 24-SOIC
VE-B5Z-MU-S CONVERTER MOD DC/DC 2V 80W
X9409WS24IT1 IC XDCP QUAD 64-TAP 10K 24-SOIC
VE-B5Y-MU-S CONVERTER MOD DC/DC 3.3V 132W
相關代理商/技術參數
參數描述
ADF4158WCCPZ 功能描述:IC FRAC-N FREQ SYNTH 24LFCSP 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:在售 類型:分?jǐn)?shù) N 合成器（RF） PLL:是 輸入:CMOS，TTL 輸出:時鐘 電路數:1 比率 - 輸入:輸出:2:1 差分 - 輸入:輸出:是/無 頻率 - 最大值:6.1GHz 分頻器/倍頻器:是/是 電壓 - 電源:2.7 V ~ 3.3 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-WFQFN 裸露焊盤 供應商器件封裝:24-LFCSP-WQ（4x4） 標準包裝:1
ADF4158WCCPZ-RL7 功能描述:IC FRAC-N FREQ SYNTH 24LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:1,000 系列:Precision Edge® 類型:時鐘/頻率合成器 PLL:無 輸入:CML，PECL 輸出:CML 電路數:1 比率 - 輸入:輸出:2:1 差分 - 輸入:輸出:是/是 頻率 - 最大:10.7GHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN 裸露焊盤，16-MLF? 供應商設備封裝:16-MLF?（3x3） 包裝:帶卷 (TR) 其它名稱:SY58052UMGTRSY58052UMGTR-ND
ADF4159 制造商:AD 制造商全稱:Analog Devices 功能描述:Direct Modulation/Fast Waveform Generating, 13 GHz, Fractional-N Frequency Synthesizer
ADF4159CCPZ 制造商:Analog Devices 功能描述:Fractional-N Frequency Synthesizer 24-Pin LFCSP EP Tray 制造商:Analog Devices 功能描述:DIRECT MODULATION/FAST WAVEFORM GENERATING, 13 GHZ, FRACTION - Trays 制造商:Analog Devices 功能描述:IC PLL FREQ SYNTHESIZER 24LFCSP 制造商:Analog Devices Inc. 功能描述:Phase Locked Loops - PLL
ADF4159CCPZ-RL7 制造商:Analog Devices 功能描述:Fractional-N Frequency Synthesizer 24-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:13GHZ FAST RAMP DIRECT MOD FRAC N PLL - Tape and Reel 制造商:Analog Devices Inc. 功能描述:Phase Locked Loops - PLL
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*