- 您現在的位置：買賣IC網 > PDF目錄19463 > ADSP-21061LASZ-176 (Analog Devices Inc)IC DSP CONTROLLER 32BIT 240MQFP PDF資料下載
參數資料
| 型號： | ADSP-21061LASZ-176 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 52/52頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSP CONTROLLER 32BIT 240MQFP |
| 產品培訓模塊： | SHARC Processor Overview |
| 標準包裝： | 1 |
| 系列： | SHARC® |
| 類型： | 浮點 |
| 接口： | 同步串行端口（SSP） |
| 時鐘速率： | 44MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 128kB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 3.30V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 240-BFQFP 裸露焊盤 |
| 供應商設備封裝： | 240-MQFP-EP（32x32） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁
Rev. D | Page 9 of 52 | May 2013
PIN FUNCTION DESCRIPTIONS
ADSP-21061 pin definitions are listed below. All pins are identi-
cal on the ADSP-21061 and ADSP-21061L. Inputs identified as
synchronous (S) must meet timing requirements with respect to
CLKIN (or with respect to TCK for TMS, TDI). Inputs identi-
fied as asynchronous (A) can be asserted asynchronously to
CLKIN (or to TCK for TRST).
Unused inputs should be tied or pulled to VDD or GND, except
for ADDR31-0, DATA47-0, FLAG3-0, SW, and inputs that have
internal pull-up or pull-down resistors (CPA, ACK, DTx, DRx,
TCLKx, RCLKx, TMS, and TDI)—these pins can be left float-
ing. These pins have a logic-level hold circuit that prevents the
input from floating internally.
Table 2. Pin Descriptions
Pin
Type
Function
ADDR31–0
I/O/T
External Bus Address.
The ADSP-21061 outputs addresses for external memory and peripherals on these
pins. In a multiprocessor system the bus master outputs addresses for read/write of the internal memory or
IOP registers of other ADSP-21061s. The ADSP-21061 inputs addresses when a host processor or multipro-
cessing bus master is reading or writing its internal memory or IOP registers.
DATA47–0
I/O/T
External Bus Data.
The ADSP-21061 inputs and outputs data and instructions on these pins. 32-bit single-
precision floating-point data and 32-bit fixed-point data is transferred over Bits 47 to 16 of the bus. 40-bit
extended-precision floating-point data is transferred over Bits 47 to 8 of the bus. 16-bit short word data is
transferred over Bits 31 to 16 of the bus. In PROM boot mode, 8-bit data is transferred over Bits 23 to 16. Pull-
up resistors on unused DATA pins are not necessary.
MS3–0
O/T
Memory Select Lines.
These lines are asserted (low) as chip selects for the corresponding banks of external
memory. Memory bank size must be defined in the ADSP-21061’s system control register (SYSCON). The
MS3–0 lines are decoded memory address lines that change at the same time as the other address lines.
When no external memory access is occurring the MS3–0 lines are inactive; they are active however when a
conditional memory access instruction is executed, whether or not the condition is true. MS0 can be used
with the PAGE signal to implement a bank of DRAM memory (Bank 0). In a multiprocessing system the MS3–0
lines are output by the bus master.
RD
I/O/T
Memory Read Strobe.
This pin is asserted (low) when the ADSP-21061 reads from external memory devices
or from the internal memory of other ADSP-21061s. External devices (including other ADSP-21061s) must
assert RD to read from the ADSP-21061’s internal memory. In a multiprocessing system RD is output by the
bus master and is input by all other ADSP-21061s.
WR
I/O/T
Memory Write Strobe.
This pin is asserted (low) when the ADSP-21061 writes to external memory devices
or to the internal memory of other ADSP-21061s. External devices must assert WR to write to the
ADSP-21061’s internal memory. In a multiprocessing system WR is output by the bus master and is input by
all other ADSP-21061s.
PAGE
O/T
DRAM Page Boundary.
The ADSP-21061 asserts this pin to signal that an external DRAM page boundary
has been crossed. DRAM page size must be defined in the ADSP-21061’s memory control register (WAIT).
DRAM can only be implemented in external memory Bank 0; the PAGE signal can only be activated for
Bank 0 accesses. In a multiprocessing system PAGE is output by the bus master.
ADRCLK
O/T
Clock Output Reference.
In a multiprocessing system ADRCLK is output by the bus master.
SW
I/O/T
Synchronous Write Select.
This signal is used to interface theADSP-21061to synchronousmemorydevices
(including other ADSP-21061s). The ADSP-21061 asserts SW (low) to provide an early indication of an
impending write cycle, which can be aborted if WR is not later asserted (e.g., in a conditional write
instruction). In a multiprocessing system, SW is output by the bus master and is input by all other
ADSP-21061s to determine if the multiprocessor memory access is a read or write. SWis asserted at the same
time as the address output. A host processor using synchronous writes must assert this pin when writing to
the ADSP-21061(s).
A = Asynchronous, G = Ground, I = Input, O = Output, P = Power Supply, S = Synchronous, (A/D) = Active Drive, (O/D) = Open-Drain,
T = Three-State (when SBTS is asserted, or when the ADSP-21061 is a bus slave)
相關PDF資料 |
PDF描述 |
|---|---|
| EBM24DCSN | CONN EDGECARD 48POS DIP .156 SLD |
| VE-2WJ-CY-F1 | CONVERTER MOD DC/DC 36V 50W |
| TAJC155K050SNJ | CAP TANT 1.5UF 50V 10% 2312 |
| ADSP-21364BSWZ-1AA | IC DSP 32BIT 333MHZ EPAD 144LQFP |
| GEC08DRTN-S13 | CONN EDGECARD 16POS .100 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-21061LKB-160 | 功能描述:IC DSP CONTROLLER 32BIT 225BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21061LKB-176 | 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer Family |
| ADSP-21061LKBZ-160 | 功能描述:IC DSP CONTROLLER 32BIT 225-BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP21061LKS160 | 制造商:Analog Devices 功能描述:DSP Floating-Point 32-Bit 40MHz 40MIPS 240-Pin MQFP Tray |
| ADSP-21061LKS-160 | 制造商:Rochester Electronics LLC 功能描述:ADSP-21061 1MBIT,40MHZ, 3V SHARC - Bulk 制造商:Analog Devices 功能描述:IC SHARC DSP 40MHZ 21061 MQFP240 |
發布緊急采購，3分鐘左右您將得到回復。