- 您現在的位置：買賣IC網 > PDF目錄19387 > ADSP-BF537BBCZ-5AV (Analog Devices Inc)IC DSP CTLR 16BIT 182CSPBGA PDF資料下載
參數資料
| 型號： | ADSP-BF537BBCZ-5AV |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/68頁 |
| 文件大小： | 0K |
| 描述： | IC DSP CTLR 16BIT 182CSPBGA |
| 產品培訓模塊： | Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services |
| 標準包裝： | 1 |
| 系列： | Blackfin® |
| 類型： | 定點 |
| 接口： | CAN，SPI，SSP，TWI，UART |
| 時鐘速率： | 533MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 132kB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 1.25V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 182-LFBGA，CSPBGA |
| 供應商設備封裝： | 182-CSPBGA（12x12） |
| 包裝： | 托盤 |
| 配用： | ADZS-BF537-ASKIT-ND - BOARD EVAL SKIT ADSP-BF537 ADZS-BFAUDIO-EZEXT-ND - BOARD EVAL AUDIO BLACKFIN ADZS-BF537-EZLITE-ND - BOARD EVAL ADSP-BF537 ADZS-BFAV-EZEXT-ND - BOARD DAUGHT ADSP-BF533,37,61KIT ADZS-BF537-STAMP-ND - SYSTEM DEV FOR ADSP-BF537 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
Rev. J
|
Page 13 of 68
|
February 2014
Output Mode
Output mode is used for transmitting video or other data with
up to three output frame syncs. Typically, a single frame sync is
appropriate for data converter applications, whereas two or
three frame syncs could be used for sending video with hard-
ware signaling.
ITU-R 656 Mode Descriptions
The ITU-R 656 modes of the PPI are intended to suit a wide
variety of video capture, processing, and transmission applica-
tions. Three distinct submodes are supported:
1. Active video only mode
2. Vertical blanking only mode
3. Entire field mode
Active Video Mode
Active video only mode is used when only the active video por-
tion of a field is of interest and not any of the blanking intervals.
The PPI does not read in any data between the end of active
video (EAV) and start of active video (SAV) preamble symbols,
or any data present during the vertical blanking intervals. In this
mode, the control byte sequences are not stored to memory;
they are filtered by the PPI. After synchronizing to the start of
Field 1, the PPI ignores incoming samples until it sees an SAV
code. The user specifies the number of active video lines per
frame (in PPI_COUNT register).
Vertical Blanking Interval Mode
In this mode, the PPI only transfers vertical blanking interval
(VBI) data.
Entire Field Mode
In this mode, the entire incoming bit stream is read in through
the PPI. This includes active video, control preamble sequences,
and ancillary data that may be embedded in horizontal and ver-
tical blanking intervals. Data transfer starts immediately after
synchronization to Field 1. Data is transferred to or from the
synchronous channels through eight DMA engines that work
autonomously from the processor core.
DYNAMIC POWER MANAGEMENT
The ADSP-BF534/ADSP-BF536/ADSP-BF537 processors pro-
vide five operating modes, each with a different performance
and power profile. In addition, dynamic power management
provides the control functions to dynamically alter the proces-
sor core supply voltage, further reducing power dissipation.
Control of clocking to each of the peripherals also reduces
power consumption. See Table 4 for a summary of the power
settings for each mode. Also, see Table 16, Table 15 and
Full-On Operating Mode—Maximum Performance
In the full-on mode, the PLL is enabled and is not bypassed,
providing capability for maximum operational frequency. This
is the power-up default execution state in which maximum per-
formance can be achieved. The processor core and all enabled
peripherals run at full speed.
Active Operating Mode—Moderate Dynamic Power
Savings
In the active mode, the PLL is enabled but bypassed. Because the
PLL is bypassed, the processor’s core clock (CCLK) and system
clock (SCLK) run at the input clock (CLKIN) frequency. In this
mode, the CLKIN to CCLK multiplier ratio can be changed,
although the changes are not realized until the full-on mode is
entered. DMA access is available to appropriately configured
L1 memories.
In the active mode, it is possible to disable the PLL through the
PLL control register (PLL_CTL). If disabled, the PLL must be
re-enabled before transitioning to the full-on or sleep modes.
Sleep Operating Mode—High Dynamic Power Savings
The sleep mode reduces dynamic power dissipation by disabling
the clock to the processor core (CCLK). The PLL and system
clock (SCLK), however, continue to operate in this mode. Typi-
cally an external event or RTC activity wakes up the processor.
When in the sleep mode, asserting wake-up causes the processor
to sense the value of the BYPASS bit in the PLL control register
(PLL_CTL). If BYPASS is disabled, the processor transitions to
the full on mode. If BYPASS is enabled, the processor transi-
tions to the active mode.
System DMA access to L1 memory is not supported in
sleep mode.
Deep Sleep Operating Mode—Maximum Dynamic Power
Savings
The deep sleep mode maximizes dynamic power savings by dis-
abling the clocks to the processor core (CCLK) and to all
synchronous peripherals (SCLK). Asynchronous peripherals,
such as the RTC, may still be running but cannot access internal
resources or external memory. This powered-down mode can
only be exited by assertion of the reset interrupt (RESET) or by
an asynchronous interrupt generated by the RTC. When in deep
sleep mode, an RTC asynchronous interrupt causes the
processor to transition to the active mode. Assertion of RESET
while in deep sleep mode causes the processor to transition to
the full-on mode.
Table 4. Power Settings
Mode
PLL
Bypassed
Core
Clock
(CCLK)
System
Clock
(SCLK)
Internal
Power
(VDDINT)
Full On
Enabled
No
Enabled
On
Active
Enabled/
Disabled
Yes
Enabled
On
Sleep
Enabled
—
Disabled Enabled
On
Deep
Sleep
Disabled
—
Disabled Disabled On
Hibernate Disabled
—
Disabled Disabled Off
相關PDF資料 |
PDF描述 |
|---|---|
| TPSD157M006Y0125 | CAP TANT 150UF 6.3V 20% 2917 |
| RW2-243.3D/H3/B | CONV DC/DC 2W 18-36VIN +/-3.3V |
| AMC26DREN | CONN EDGECARD 52POS .100 EYELET |
| ACC40DREN | CONN EDGECARD 80POS .100 EYELET |
| RCC05DRYH | CONN EDGECARD 10POS DIP .100 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-BF537BBCZ-5AV | 制造商:Analog Devices 功能描述:Digital Signal Processor IC |
| ADSP-BF537BBCZ5AVX | 制造商:Analog Devices 功能描述:- Trays |
| ADSP-BF537BBCZ-5AVX | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADSP-BF537BBCZ-5AX | 制造商:Analog Devices 功能描述:182-MBGA PB-FREE - Trays |
| ADSP-BF537BBCZ-5B | 功能描述:IC DSP CTLR 16BIT 208CSPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:Blackfin® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。