參數資料
型號： ADUC7023BCP6Z62IRL
廠商： Analog Devices Inc
文件頁數： 47/96頁
文件大?。?/td> 0K
描述： IC MCU 12BIT 62KB FLASH 40LFCSP
標準包裝： 2,500
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 44MHz
連通性： I²C，SPI
外圍設備： POR，PWM，WDT
輸入/輸出數： 20
程序存儲器容量： 64KB（32K x 16）
程序存儲器類型： 閃存
RAM 容量： 2K x 32
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
數據轉換器： A/D 12 x12b; D/A 4x12b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 40-VFQFN 裸露焊盤，CSP
包裝： 帶卷 (TR)
Data Sheet
ADuC7023
| Page 51 of 96
DIGITAL PERIPHERALS
GENERAL-PURPOSE INPUT/OUTPUT
The ADuC7023 provides up to 20 general-purpose, bidirectional
I/O (GPIO) pins. All I/O pins apart from the pins shared with the
ADC are 5 V tolerant, meaning the GPIOs support an input voltage
of 5 V. The shared ADC pins only support an input up to AVDD.
In general, many of the GPIO pins have multiple functions (see
Table 55 for the pin function definitions). By default, the GPIO
pins are configured in GPIO mode.
All GPIO pins have an internal pull-up resistor (of about 100 kΩ)
and their drive capability is 1.6 mA. Note that a maximum of
20 GPIOs can drive 1.6 mA at the same time. Using the GPxPAR
registers, it is possible to enable/disable the pull-up resistors.
The 20 GPIOs are grouped in three ports, Port 0 to Port 2 (Port x).
Each port is controlled by four or five MMRs.
The input level of any GPIO can be read at any time in the
GPxDAT MMR, even when the pin is configured in a mode
other than GPIO. The PLA input is always active.
When the ADuC7023 part enters a power-saving mode, the
GPIO pins retain their state. Also note, that by setting RSTCFG
bit 0, the GPIO pins can retain their state during a watchdog or
software reset.
Table 55. GPIO Pin Function Descriptions
Configuration
Port
Pin
00
01
10
11
0
P0.0
GPIO/BM
nTRST
ADCBUSY
PLAI[8]
GPIO
TDO
PLAI[9]
GPIO
TDI
PLAO[8]
GPIO
TCK
PLAO[9]
P0.4
GPIO/IRQ0
SCL0
CONVSTART
PLAI[0]
P0.5
GPIO
SDA0
COMPOUT
PLAI[1]
P0.6
GPIO
MISO
PLAI[2]
P0.7
GPIO
MOSI
SDA12
PLAO[0]
1
P1.0
GPIO
SCLK
PWM0
PLAO[1]
P1.1
GPIO/IRQ1
SS
PWM1
PLAO[2]
GPIO/IRQ2
ADC4
ECLK
PLAI[3]
P1.3
GPIO/IRQ3
ADC5
PLAI[4]
P1.4
GPIO
ADC10
PLAO[3]
P1.5
GPIO
ADC6
PWMTRIPINPUT
PLAO[4]
P1.6
GPIO
PWM2
PLAI[5]
P1.7
GPIO
SDA14
PWM3
PLAI[6]
2
P2.0
GPIO
ADC12
PWM4
PLAI[7]
P2.2
GPIO
ADC7
PWMsync
PLAO[6]
P2.3
GPIO
ADC8
PLAO[7]
P2.4
GPIO
ADC9
PLAI[10]
1 These pins should not be used by user code when debugging the part via
JTAG. See Table 36 for further details on how to configure these pins for
GPIO mode. The default value of these pins depends on the level of the
P0.0/BM pin during the last reset sequence.
2 I2C1 function is only available on the 32-lead and 36-ball packages.
3 When configured in Mode 2, P1.2 is ECLK by default, or core clock output. To
configure it as a clock input, the MDCLK bits in PLLCON must be set to 11.
4 I2C1 function is only available on the 40-lead package.
GPxCON Registers
Name
Address
Default Value
Access
GP0CON
0xFFFFF400
0x00001111
R/W
GP1CON
0xFFFFF404
0x00000000
R/W
GP2CON
0xFFFFF408
0x00000000
R/W
GPxCON are the Port x control registers, which select the
function of each pin of Port x as described in Table 56.
Table 56. GPxCON MMR Bit Descriptions
Bit
Description
31 to 30
Reserved.
29 to 28
Select function of Px.7 pin.
27 to 26
Reserved.
25 to 24
Select function of Px.6 pin.
23 to 22
Reserved.
21 to 20
Select function of Px.5 pin.
19 to 18
Reserved.
17 to 16
Select function of Px.4 pin.
15 to 14
Reserved.
13 to 12
Select function of Px.3 pin.
11 to 10
Reserved.
9 to 8
Select function of Px.2 pin.
7 to 6
Reserved.
5 to 4
Select function of Px.1 pin.
3 to 2
Reserved.
1 to 0
Select function of Px.0 pin.
GP0PAR Register
Name
GP0PAR
Address
0xFFFFF42C
Default value
0x22220000
Access
Read/write
Function
GP0PAR programs the parameters for Port 0,
Port 1, and Port 2. Note that the GP0DAT
MMR must always be written after changing
the GP0PAR MMR.
GP1PAR Register
Name
GP1PAR
Address
0xFFFFF43C
Default value
0x22000022
Access
Read/write
Function
GP1PAR programs the parameters for Port 0,
Port 1, and Port 2. Note that the GP1DAT
MMR must always be written after changing
the GP1PAR MMR.
Rev. E
相關PDF資料
PDF描述
ADUC7023BCPZ62I-RL IC MCU 12BIT 62KB FLASH 32LFCSP
ATMEGA32L-8MUR MCU AVR 32K FLASH 8MHZ 44QFN
ATMEGA32-16MUR MCU AVR 32KB FLASH 16MHZ 44QFN
ADG528ATQ IC MULTIPLEXER 8X1 18CDIP
AD7511DIKNZ IC SWITCH QUAD SPST 16DIP
相關代理商/技術參數
參數描述
ADUC7023BCPZ62I 功能描述:IC MCU 12BIT 62KB FLASH 32LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587
ADUC7023BCPZ62I-R7 功能描述:IC MCU 12BIT 62KB FLASH 32LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7023BCPZ62I-RL 功能描述:IC MCU 12BIT 62KB FLASH 32LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7024 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC7024BCP62 制造商:Analog Devices 功能描述:FLASH ARM7+10-CH,12-B ADC &2X12-B DAC IC - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*