參數資料
型號： ADUC7122BBCZ
廠商： Analog Devices Inc
文件頁數： 66/96頁
文件大小： 0K
描述： IC ARM7TDMI MCU 126KB 108CSPBGA
特色產品： ADuC7122 Precision Analog Microcontroller
標準包裝： 1
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 41.78MHz
連通性： I²C，SPI，UART/USART
外圍設備： POR，PWM，WDT
輸入/輸出數： 32
程序存儲器容量： 126KB（63K x 16）
程序存儲器類型： 閃存
RAM 容量： 8K x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 3.6 V
數據轉換器： A/D 13x12b，D/A 12x12b
振蕩器型： 內部
工作溫度： -10°C ~ 95°C
封裝/外殼： 108-LFBGA，CSPBGA
包裝： 托盤
ADuC7122
Rev. 0 | Page 69 of 96
SERIAL PERIPHERAL INTERFACE
The ADuC7122 integrates a complete hardware serial peri-
pheral interface (SPI) on chip. SPI is an industry standard,
synchronous serial interface that allows eight bits of data to
be synchronously transmitted and simultaneously received,
that is, full duplex up to a maximum bit rate of 20 Mb.
The SPI port can be configured for master or slave operation
and typically consists of four pins: SPIMISO, SPIMOSI,
SPICLK, and SPICS.
SPIMISO (MASTER IN, SLAVE OUT) PIN
The SPIMISO pin is configured as an input line in master mode
and an output line in slave mode. The SPIMISO line on the
master (data in) should be connected to the SPIMISO line in
the slave device (data out). The data is transferred as byte wide
(8-bit) serial data, MSB first.
SPIMOSI (MASTER OUT, SLAVE IN) PIN
The SPIMOSI pin is configured as an output line in master
mode and an input line in slave mode. The SPIMOSI line on the
master (data out) should be connected to the SPIMOSI line in
the slave device (data in). The data is transferred as byte wide
(8-bit) serial data, MSB first.
SPICLK (SERIAL CLOCK I/O) PIN
The master serial clock (SPICLK) synchronizes the data being
transmitted and received through the MOSI SPICLK period.
Therefore, a byte is transmitted/received after eight SPICLK
periods. The SPICLK pin is configured as an output in master
mode and as an input in slave mode.
In master mode, polarity and phase of the clock are controlled
by the SPICON register, and the bit rate is defined in the
SPIDIV register as follows:
)
1
(
2
SPIDIV
f
UCLK
CLOCK
SERIAL
The maximum speed of the SPI clock is independent on the
clock divider bits.
In slave mode, the SPICON register must be configured with
the phase and polarity of the expected input clock. The slave
accepts data from an external master up to 10 Mb.
In both master and slave modes, data is transmitted on one edge
of the SPICLK signal and sampled on the other. Therefore, it is
important that the polarity and phase are configured the same
for the master and slave devices.
SPI CHIP SELECT (SPICS INPUT) PIN
In SPI slave mode, a transfer is initiated by the assertion of
SPICS, which is an active low input signal. The SPI port then
transmits and receives 8-bit data until the transfer is concluded
by deassertion of SPICS. In slave mode, SPICS is always an input.
In SPI master mode, SPICS is an active low output signal. It
asserts itself automatically at the beginning of a transfer and
deasserts itself upon completion.
CONFIGURING EXTERNAL PINS FOR SPI
FUNCTIONALITY
The SPI pins of the ADuC7122 device are P0.2 to P0.5.
P0.5 is the slave chip select pin. In slave mode, this pin is an
input and must be driven low by the master. In master mode,
this pin is an output and goes low at the beginning of a transfer
and high at the end of a transfer.
P0.2 is the SPICLK pin.
P0.3 is the master in, slave out (SPIMISO) pin.
P0.4 is the master out, slave in (SPIMOSI) pin.
To configure P0.2 to P0.5 for SPI mode, see the General-
相關PDF資料
PDF描述
AT91SAM9261B-CU MCU ARM9 ULTRA LOW PWR 217-LFBGA
VJ1825A183JBAAT4X CAP CER 0.018UF 50V 5% NP0 1825
ATMEGA128-16MU IC AVR MCU 128K 16MHZ 5V 64-QFN
VJ1825A183KBAAT4X CAP CER 0.018UF 50V 10% NP0 1825
ATMEGA128L-8MU IC AVR MCU 128K 8MHZ 3V 64-QFN
相關代理商/技術參數
參數描述
ADUC7122BBCZ-RL 功能描述:PRECISION ANALOG MCU I.C RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7124 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller, 12-Bit Analog I/O, Large Memory, ARM7TDMI MCU with Enhanced IRQ Handler
ADUC7124BCPZ126 功能描述:IC DAS MCU ARM7 ADC/DDS 64LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587
ADUC7124BCPZ126-RL 功能描述:IC DAS MCU ARM7 ADC/DDS 64-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7126BSTZ126 功能描述:IC MCU 16/32B 126KB FLASH 80LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*