參數資料
型號： AM29F017D-120FD
廠商： SPANSION LLC
元件分類： PROM
英文描述： 2M X 8 FLASH 5V PROM, 120 ns, PDSO48
封裝： MO-142DD, TSOP-48
文件頁數： 4/46頁
文件大小： 1387K
代理商： AM29F017D-120FD
10
Am29F017D
July 29, 2005
read specifications apply. Refer to “Write Operation
Status” for more information, and to each AC Charac-
teristics section for timing diagrams.
Standby Mode
When the system is not reading or writing to the device,
it can place the device in the standby mode. In this
mode, current consumption is greatly reduced, and the
outputs are placed in the high impedance state, inde-
pendent of the OE# input.
The device enters the CMOS standby mode when CE#
and RESET# pins are both held at VCC ± 0.5 V. (Note
that this is a more restricted voltage range than VIH.)
The device enters the TTL standby mode when CE#
and RESET# pins are both held at VIH. The device re-
quires standard access time (tCE) for read access when
the device is in either of these standby modes, before it
is ready to read data.
The device also enters the standby mode when the RE-
SET# pin is driven low. Refer to the next section, “RE-
If the device is deselected during erasure or program-
ming, the device draws active current until the
operation is completed.
In the DC Characteristics tables, ICC3 represents the
standby current specification.
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of reset-
ting the device to reading array data. When the system
drives the RESET# pin low for at least a period of tRP,
the device immediately terminates any operation in
progress, tristates all data output pins, and ignores all
read/write attempts for the duration of the RESET#
pulse. The device also resets the internal state ma-
chine to reading array data. The operation that was in-
terrupted should be reinitiated once the device is ready
to accept another command sequence, to ensure data
integrity.
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at VIL, the device enters
the TTL standby mode; if RESET# is held at VSS ±
0.5 V, the device enters the CMOS standby mode.
The RESET# pin may be tied to the system reset cir-
cuitry. A system reset would thus also reset the Flash
memory, enabling the system to read the boot-up firm-
ware from the Flash memory.
If RESET# is asserted during a program or erase oper-
ation, the RY/BY# pin remains a “0” (busy) until the in-
ternal reset operation is complete, which requires a
time of tREADY (during Embedded Algorithms). The
system can thus monitor RY/BY# to determine whether
the reset operation is complete. If RESET# is asserted
when a program or erase operation is not executing
(RY/BY# pin is “1”), the reset operation is completed
within a time of tREADY (not during Embedded Algo-
rithms). The system can read data tRH after the RE-
SET# pin returns to VIH.
Refer to the AC Characteristics tables for RESET# pa-
rameters and timing diagram.
Output Disable Mode
When the OE# input is at VIH, output from the device is
disabled. The output pins are placed in the high imped-
ance state.
相關PDF資料
PDF描述
AM29LV004T-70RFF 512K X 8 FLASH 3V PROM, 70 ns, PDSO40
AM29LV004T-80EF 512K X 8 FLASH 3V PROM, 80 ns, PDSO40
AT28C1024-20BM/883 64K X 16 EEPROM 5V, 200 ns, CDIP40
AM99C641-45/LMC 64K X 1 STANDARD SRAM, 45 ns, CQCC22
AM27128A-15LIB 16K X 8 UVPROM, 150 ns, CQCC32
相關代理商/技術參數
參數描述
AM29F017D-70FI 制造商:Spansion 功能描述:FLASH PARALLEL 5V 16MBIT 2MX8 70NS 48TSOP - Trays
am29f017d-90fc/t 制造商:Advanced Micro Devices 功能描述:
AM29F032B-120ED 制造商:Spansion 功能描述:
AM29F032B75ED 制造商:Advanced Micro Devices 功能描述:
AM29F032B-75EF 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:32M (4M X 8-BIT) 5V FLSH SCTR 制造商:Spansion 功能描述:IC, FLASH MEM, 32MBIT, 75NS, 40-TSOP, Memory Type:Flash - NOR, Memory Size:32Mbi
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*