參數資料
型號： AM79C972BKIW
廠商： ADVANCED MICRO DEVICES INC
元件分類： 微控制器/微處理器
英文描述： PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
中文描述： 5 CHANNEL(S), 100M bps, LOCAL AREA NETWORK CONTROLLER, PQFP16
封裝： PLASTIC, QFP-160
文件頁數： 16/130頁
文件大小： 1580K
代理商： AM79C972BKIW
16
Am79C972
PIN DESCRIPTIONS
PCI Interface
AD[31:0]
Address and Data
Address and data are multiplexed on the same bus in-
terface pins. During the first clock of a transaction,
AD[31:0] contain a physical address (32 bits). During
the subsequent clocks, AD[31:0] contain data. Byte or-
dering is little endian by default. AD[7:0] are defined as
the least significant byte (LSB) and AD[31:24] are de-
fined as the most significant byte (MSB). For FIFO data
transfers, the Am79C972 controller can be pro-
grammed for big endian byte ordering. See CSR3, bit 2
(BSWP) for more details.
Input/Output
During the address phase of the transaction, when the
Am79C972 controller is a bus master, AD[31:2] will ad-
dress the active Double Word (DWord). The
Am79C972 controller always drives AD[1:0] to
’
00
’
dur-
ing the address phase indicating linear burst order.
When the Am79C972 controller is not a bus master, the
AD[31:0] lines are continuously monitored to determine
if an address match exists for slave transfers.
During the data phase of the transaction, AD[31:0] are
driven by the Am79C972 controller when performing
bus master write and slave read operations. Data on
AD[31:0] is latched by the Am79C972 controller when
performing bus master read and slave write operations.
When RST is active, AD[31:0] are inputs for NAND tree
testing.
C/BE[3:0]
Bus Command and Byte Enables Input/Output
Bus command and byte enables are multiplexed on the
same bus interface pins. During the address phase of
the transaction, C/BE[3:0] define the bus command.
During the data phase, C/BE[3:0] are used as byte en-
ables. The byte enables define which physical byte
lanes carry meaningful data. C/BE0 applies to byte 0
(AD[7:0]) and C/BE3 applies to byte 3 (AD[31:24]). The
function of the byte enables is independent of the byte
ordering mode (BSWP, CSR3, bit 2).
When RST is active, C/BE[3:0] are inputs for NAND
tree testing
.
CLK
Clock
This clock is used to drive the system bus interface and
the internal buffer management unit. All bus signals are
sampled on the rising edge of CLK and all parameters
are defined with respect to this edge. The Am79C972
controller normally operates over a frequency range of
10 to 33 MHz on the PCI bus due to networking de-
mands. See the
Frequency Demands for Network Op-
Input
eration
section for details. The Am79C972 controller
will support a clock frequency of 0 MHz after certain
precautions are taken to ensure data integrity. This
clock or a derivation is not used to drive any network
functions.
When RST is active, CLK is an input for NAND tree
testing
.
DEVSEL
Device Select
The Am79C972 controller drives DEVSEL when it de-
tects a transaction that selects the device as a target.
The device samples DEVSEL to detect if a target
claims a transaction that the Am79C972 controller has
initiated.
Input/Output
When RST is active, DEVSEL is an input for NAND tree
testing
.
FRAME
Cycle Frame
FRAME is driven by the Am79C972 controller when it
is the bus master to indicate the beginning and duration
of a transaction. FRAME is asserted to indicate a bus
transaction is beginning. FRAME is asserted while
data transfers continue. FRAME is deasserted before
the final data phase of a transaction. When the
Am79C972 controller is in slave mode, it samples
FRAME to determine the address phase of a transac-
tion.
Input/Output
When RST is active, FRAME is an input for NAND tree
testing
.
GNT
Bus Grant
This signal indicates that the access to the bus has
been granted to the Am79C972 controller.
Input
The Am79C972 controller supports bus parking. When
the PCI bus is idle and the system arbiter asserts GNT
without an active REQ from the Am79C972 controller,
the device will drive the AD[31:0], C/BE[3:0] and PAR
lines.
When RST is active, GNT is an input for NAND tree
testing
.
IDSEL
Initialization Device Select
This signal is used as a chip select for the Am79C972
controller during configuration read and write transac-
tions.
Input
When RST is active, IDSEL is an input for NAND tree
testing
.
相關PDF資料
PDF描述
AM79C972BVCW PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
AM79C972 PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
AM79C972BVIW PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
AM79C974 PCnetTM-SCSI Combination Ethernet and SCSI Controller for PCI Systems
AM79C974KCW PCnetTM-SCSI Combination Ethernet and SCSI Controller for PCI Systems
相關代理商/技術參數
參數描述
AM79C972BVC 制造商:Advanced Micro Devices 功能描述:
AM79C972BVC\W 制造商:Advanced Micro Devices 功能描述:Ethernet CTLR Single Chip 10Mbps/100Mbps 3.3V 176-Pin TQFP Tray 制造商:Advanced Micro Devices 功能描述:5 CHANNEL(S), 100M bps, LOCAL AREA NETWORK CONTROLLER, PQFP176
AM79C972BVCW 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
AM79C972BVD\\W 制造商:Advanced Micro Devices 功能描述:
AM79C972BVD\W 制造商:Advanced Micro Devices 功能描述:Ethernet CTLR Single Chip 10Mbps/100Mbps 3.3V 176-Pin TQFP Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*