參數資料
型號： AT42QT1110-AZ
廠商： ATMEL CORP
元件分類： 速度傳感器和接近開關
英文描述： PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT
封裝： 7 X 7 MM, 1 MM HEIGHT, 0.80 MM PITCH, ROHS COMPLIANT, PLASTIC, TQFP-32
文件頁數： 15/46頁
文件大?。?/td> 657K
代理商： AT42QT1110-AZ
22
9570I–AT42–03/10
AT42QT1110-MZ/AT42QT1110-AZ
5.
Control Commands
5.1
Introduction
The QT1110 control commands are those commands that affect the device operation.
The control commands are listed in Table 5-1 and are described individually in the following
sections.
Note:
Commands are implemented immediately upon reception, so a suitable delay is
required for the operation to be completed before communications can be
re-established.
5.2
Send Setups (0x01)
This command initiates the upload of the full settings table to the QT1110 (see Section 7 on
When this command is received, the QT1110 stops key measurement and waits until 42 bytes of
setup data have been received. Key acquisition will restart after all the setup data has been
received.
If enabled, a CRC check byte is transmitted (both ways) after the 42 bytes to confirm that they
have been received correctly.
If CRC checking is not enabled, it is recommended that the host request a dump of setup data
from the QT1110, and confirms that the data correctly matches the data sent.
The host must wait for at least 150 s for the operation to be completed before communications
can be re-established.
5.3
Calibrate All (0x03)
This command initiates the recalibration of all sensor keys.
The host must wait for at least 150 s for the operation to be completed before communications
can be re-established.
Table 5-1.
Control Commands
Command
Code
Note
Send Setups
0x01
Configures the device to receive setup data
Calibrate All
0x03
Calibrates all keys
Reset
0x04
Resets the device
Sleep
0x05
Sleep (dead) mode
Store to EEPROM
0x0A
Stores RAM setups to EEPROM
Restore from EEPROM
0x0B
Copies EEPROM setups to RAM (automatically done at
startup)
Erase EEPROM
0x0C
Erases EEPROM setups
Recover EEPROM
0x0D
Restores last EEPROM settings (after erase)
Calibrate Key 'k'
0x1k
Calibrates one key (key k)
相關PDF資料
PDF描述
AT42QT1110-MZ PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT
AT42QT1111-AU PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT
AT76C453AC-MY19T IMAGE SENSOR-CMOS, 708(H) X 494(V) PIXEL, 30fps, SURFACE MOUNT
ATF-33143-TR2 X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET
ATF-33143-BLK X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET
相關代理商/技術參數
參數描述
AT42QT1110-MU 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
AT42QT1110-MU QS470 功能描述:IC TOUCH SENSOR 11KEY 32QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QTouch™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AT42QT1110-MUR 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC 制造商:microchip technology 系列:* 包裝:剪切帶（CT） 零件狀態:在售 封裝/外殼:32-VFQFN 裸露焊盤 供應商器件封裝:32-QFN（5x5） 標準包裝:1
AT42QT1110-MZ 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
AT42QT1111-AU 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*