參數資料
型號： AT42QT1110-AZ
廠商： ATMEL CORP
元件分類： 速度傳感器和接近開關
英文描述： PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT
封裝： 7 X 7 MM, 1 MM HEIGHT, 0.80 MM PITCH, ROHS COMPLIANT, PLASTIC, TQFP-32
文件頁數： 16/46頁
文件大小： 657K
代理商： AT42QT1110-AZ
23
9570I–AT42–03/10
AT42QT1110-MZ/AT42QT1110-AZ
5.4
Reset (0x04)
The Reset command forces the QT1110 to reset. If the setups data is present in the EEPROM,
the setups are loaded into the device. Otherwise default settings are applied.
The host must wait for at least 160 ms for the operation to be completed before communications
can be re-established.
5.5
Sleep (0x05)
The Sleep command puts the device into sleep mode (see Section 4.3 on page 17).
The host must wait for at least 150 s after a low signal is applied to the SS or CHANGE pin to
wake the device before communications can be re-established.
5.6
Store to EEPROM (0x0A)
Stores the current RAM contents to the QT1110’s internal EEPROM. When the device is reset, it
will automatically reload these settings.
The host must wait for at least 200 ms for the operation to be completed before communications
can be re-established.
5.7
Restore from EEPROM (0x0B)
Settings stored in EEPROM are automatically loaded into RAM when the device is reset. If
desired, these settings can be re-loaded into RAM using the ‘Restore from EEPROM’ command.
The host must wait for at least 150 ms for the operation to be completed before communications
can be re-established.
5.8
Erase EEPROM (0x0C)
This command erases the settings stored in EEPROM and then resets the QT1110. This causes
the QT1110 to revert to its default settings.
The host must wait for at least 50 ms for the operation to be completed before communications
can be re-established.
5.9
Recover EEPROM (0x0D)
This command “undeletes” the setup data that was previously stored in the device’s EEPROM
and has been erased using the “Erase EEPROM” command.
Note:
If valid settings have not previously been stored in the device EEPROM, the QT1110
continues to operate under the default settings.
The host must wait for at least 50 ms for the operation to be completed before communications
can be re-established.
5.10
Calibrate Key (0x1k)
This command recalibrates the key specified by “k”. For example, to calibrate key 4, the host
sends “0x14”; to calibrate key 10, the host sends “0x1A”.
The host must wait for at least 150 s for the operation to be completed before communications
can be re-established.
相關PDF資料
PDF描述
AT42QT1110-MZ PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT
AT42QT1111-AU PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT
AT76C453AC-MY19T IMAGE SENSOR-CMOS, 708(H) X 494(V) PIXEL, 30fps, SURFACE MOUNT
ATF-33143-TR2 X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET
ATF-33143-BLK X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET
相關代理商/技術參數
參數描述
AT42QT1110-MU 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
AT42QT1110-MU QS470 功能描述:IC TOUCH SENSOR 11KEY 32QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QTouch™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AT42QT1110-MUR 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC 制造商:microchip technology 系列:* 包裝:剪切帶（CT） 零件狀態:在售 封裝/外殼:32-VFQFN 裸露焊盤 供應商器件封裝:32-QFN（5x5） 標準包裝:1
AT42QT1110-MZ 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
AT42QT1111-AU 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*