- 您現在的位置：買賣IC網 > PDF目錄3772 > ATTINY2313V-10SUR (Atmel)IC MCU AVR 2K FLASH 20SOIC PDF資料下載
參數資料
| 型號： | ATTINY2313V-10SUR |
| 廠商： | Atmel |
| 文件頁數： | 58/225頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU AVR 2K FLASH 20SOIC |
| 產品培訓模塊： | tinyAVR Introduction |
| 標準包裝： | 1,000 |
| 系列： | AVR® ATtiny |
| 核心處理器： | AVR |
| 芯體尺寸： | 8-位 |
| 速度： | 10MHz |
| 連通性： | SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 18 |
| 程序存儲器容量： | 2KB（1K x 16） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 128 x 8 |
| RAM 容量： | 128 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.8 V ~ 5.5 V |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 20-SOIC（0.295"，7.50mm 寬） |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | ATTINY2313V-10SUR-ND ATTINY2313V-10SURTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁
PIC16F72X/PIC16LF72X
DS41341E-page 150
2009 Microchip Technology Inc.
16.1.2
AUSART ASYNCHRONOUS
RECEIVER
The Asynchronous mode is typically used in RS-232
systems. The receiver block diagram is shown in
Figure 16-2. The data is received on the RX/DT pin and
drives the data recovery block. The data recovery block
is actually a high-speed shifter operating at 16 times
the baud rate, whereas the serial Receive Shift
Register (RSR) operates at the bit rate. When all 8 or 9
bits of the character have been shifted in, they are
immediately transferred to a two character First-In
First-Out (FIFO) memory. The FIFO buffering allows
reception of two complete characters and the start of a
third character before software must start servicing the
AUSART receiver. The FIFO and RSR registers are not
directly accessible by software. Access to the received
data is via the RCREG register.
16.1.2.1
Enabling the Receiver
The AUSART receiver is enabled for asynchronous
operation by configuring the following three control bits:
CREN = 1
SYNC = 0
SPEN = 1
All other AUSART control bits are assumed to be in
their default state.
Setting the CREN bit of the RCSTA register enables the
receiver circuitry of the AUSART. Clearing the SYNC bit
of the TXSTA register configures the AUSART for
asynchronous operation. Setting the SPEN bit of the
RCSTA
register
enables
the
AUSART
and
automatically configures the RX/DT I/O pin as an input.
16.1.2.2
Receiving Data
The receiver data recovery circuit initiates character
reception on the falling edge of the first bit. The first bit,
also known as the Start bit, is always a zero. The data
recovery circuit counts one-half bit time to the center of
the Start bit and verifies that the bit is still a zero. If it is
not a zero then the data recovery circuit aborts
character reception, without generating an error, and
resumes looking for the falling edge of the Start bit. If
the Start bit zero verification succeeds then the data
recovery circuit counts a full bit time to the center of the
next bit. The bit is then sampled by a majority detect
circuit and the resulting ‘0’ or ‘1’ is shifted into the RSR.
This repeats until all data bits have been sampled and
shifted into the RSR. One final bit time is measured and
the level sampled. This is the Stop bit, which is always
a ‘1’. If the data recovery circuit samples a ‘0’ in the
Stop bit position then a framing error is set for this
character, otherwise the framing error is cleared for this
character.
Refer
to
Framing Error” for more information on framing
errors.
Immediately after all data bits and the Stop bit have
been received, the character in the RSR is transferred
to the AUSART receive FIFO and the RCIF interrupt
flag bit of the PIR1 register is set. The top character in
the FIFO is transferred out of the FIFO by reading the
RCREG register.
16.1.2.3
Receive Interrupts
The RCIF interrupt flag bit of the PIR1 register is set
whenever the AUSART receiver is enabled and there is
an unread character in the receive FIFO. The RCIF
interrupt flag bit is read-only, it cannot be set or cleared
by software.
RCIF interrupts are enabled by setting all of the
following bits:
RCIE interrupt enable bit of the PIE1 register
PEIE peripheral interrupt enable bit of the
INTCON register
GIE global interrupt enable bit of the INTCON
register
The RCIF interrupt flag bit of the PIR1 register will be
set when there is an unread character in the FIFO,
regardless of the state of interrupt enable bits.
Note:
When the SPEN bit is set the TX/CK I/O
pin is automatically configured as an
output, regardless of the state of the
corresponding TRIS bit and whether or not
the AUSART transmitter is enabled. The
PORT latch is disconnected from the
output driver so it is not possible to use the
TX/CK pin as a general purpose output.
Note:
If the receive FIFO is overrun, no additional
characters will be received until the overrun
condition
is
cleared.
Refer
to
Error” for more information on overrun
errors.
相關PDF資料 |
PDF描述 |
|---|---|
| CAT9554YI-GT2 | IC I/O EXPANDER I2C 8B 16TSSOP |
| CAT9554AYI-GT2 | IC I/O EXPANDER I2C 8B 16TSSOP |
| ATTINY44-20SSUR | MCU AVR 4KB FLASH 20MHZ 14SOIC |
| ATTINY24-20SSUR | MCU AVR 2KB FLASH 20MHZ 14SOIC |
| PCA8575PW,112 | IC I/O EXPANDER I2C 16B 24TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATTINY2313V-12PI | 制造商:Atmel Corporation 功能描述:MCU 8-bit ATtiny AVR RISC 2KB Flash 2.5V/3.3V/5V 20-Pin PDIP |
| ATTINY2313V-8MI | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit AVR Microcontroller with 2K Bytes In-System Programmable Flash |
| ATTINY2313V-8MJ | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit AVR Microcontroller with 2K Bytes In-System Programmable Flash |
| ATTINY2313V-8PI | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit AVR Microcontroller with 2K Bytes In-System Programmable Flash |
| ATTINY2313V-8PJ | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit AVR Microcontroller with 2K Bytes In-System Programmable Flash |
發布緊急采購，3分鐘左右您將得到回復。