- 您現(xiàn)在的位置：買賣IC網 > PDF目錄1908 > CC-2401K2A-CS (Copeland Communications Inc)MODEM 2400BAUD SECURE 3.3V PDF資料下載
參數資料
| 型號： | CC-2401K2A-CS |
| 廠商： | Copeland Communications Inc |
| 文件頁數： | 5/66頁 |
| 文件大?。?/td> | 0K |
| 描述： | MODEM 2400BAUD SECURE 3.3V |
| 標準包裝： | 30 |
| 數據格式： | V.21，V.22，V.23，Bell 103 |
| 波特率： | 2.4k |
| 電源電壓： | 3 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 模塊 |
| 包裝： | 散裝 |
| 配用： | 539-1002-ND - KIT EVALUATION WORLD MODEM II |
| 其它名稱： | 539-1010 CC-2401K2A-CS-ND |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
Data Sheet
CC-2401K2
Page 13 of 66
2007, Copeland Communications, Inc.
CC-2401K2 Datasheet Rev 1.5
During this event, if the NLR result code is enabled by setting S62[1](NLR) = 1, the “I” result code is sent.
Once the loop current returns to a normal current state, the “L” result code is sent. The INT# pin is also
asserted if enabled.
Loss of Carrier Detection
The CC-2401 has two methods of implementing a loss of carrier function. If GPIO4 is programmed as INT#
and if S08[7](CDM)=1, INT# asserts in data mode when a loss of carrier is detected. The carrier detect
function may also be implemented on GPIO2 by setting SE2[3:2] (GPIO2) = 01 and SOC[7](CDE) = 1.
Overcurrent Detection
The CC-2401 begins monitoring for an overcurrent condition at a programmable time set by S32 (OCDT) after
going off-hook (default = 20ms). If an overcurrent condition is detected, the CC-2401 sets S09[1] interrupt
status.
As long as GPIO4 is programmed as INT and the overcurrent mask bit is enabled by setting
S08[1](OCDM) = 1, INT asserts during an overcurrent situation. The host may then check S09[1] (OCD) via
the AT:I command to confirm that an overcurrent condition occurred.
Caller ID Monitor/Bellcore Caller ID
The CC-2401 continuously monitors the phone line for the caller ID mark signals.
This can be useful in
systems that require detection of caller ID data before the ring signal, voice mail indicator signals and Type II
caller ID monitor support. To force the CC-2401 into caller ID monitor mode, set SOC[6:5] (CIDM) = 11.
NOTE: CIDM should be disabled before going off-hook.
UK Caller ID
The CC-2401 starts searching for the Idle State Tone Alert Signal. When this signal has been detected, the
modem transmits an “a” to the host. After the Idle State Tone Alert Signal is completed, the modem applies
the wetting pulse for the required 15 ms by quickly going off-hook and on-hook. From this point on, the
algorithm is identical to that of Bellcore in that it searches for the channel seizure signal and the marks before
echoing an “m” and then reports the decoded caller ID data.
V.23 Operation / V.23 Reversing
The CC-2401 supports full V.23 operation including the V.23 reversing procedure. V.23 operation is enabled
by setting S07 (MF1) = xx10xx00b of xx01xx00b. If S07[5] (V23R) = 1, the CC-2401 receives data at 75 bps
and receives data at 600 or 1200 bps. If S07[4] (V23T) = 1, the CC-2401 Receives data at 75 bps and
transmits data at 600 or 1200 bps. S07[2] (BAUD) is the 1200 or 600 bps indicator. BAUD = 1 b enables the
1200/600 V.23 channel to run at 1200 bps, while BAUD = 0b enables 600 bps operation.
When a V.23 connection is established, the modem responds with a “c” if the connection is made with the
modem transmitting at 1200/600 bps and receiving at 75 bps. The modem responds with a “v” character if a
V.23 connection is established with the modem transmitting at 75 bps and receiving at 1200/600 bps.
The CC-2401 supports V.23 turnaround procedure, allowing a modem that is transmitting at 75 bps to initiate a
“turnaround” procedure so it can begin transmitting data at 1200/600 bps and receiving data at 75 bps. The
modem is defined as being in V.23 master mode if it is transmitting at 75 bps and as being in slave m ode if it is
transmitting at 1200/600 bps.
Modem in Master Mode
To perform a direct turnaround once a modem connection is established, the master host goes into online
command mode by sending an escape command (Escape pin activation, TIES, or ninth bit escape) to the
master modem.
NOTE: The host can initiate a turnaround only if the CC-2401 is the master.
相關PDF資料 |
PDF描述 |
|---|---|
| CC-2434K2-CS5 | MODEM FAX 33K 5V |
| CC-24K2N-CS5 | MODEM WORLD NET 2400BAUD 5V |
| CC-92K2-IS | MODEM 56KBAUD V.90 SERIAL 3.3V |
| CC-MX-LB69-ZM | CONNECTCORE I.MX51 MODULE |
| CD22M3494MQZ96 | IC CROSSPOINT SWITCH 16X8 44PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CC-2401K2A-CS5 | 功能描述:MODEM 2400BAUD SECURE 5V RoHS:否 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:- 標準包裝:25 系列:- 數據格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
| CC24020N | 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Super Fast Recovery Dual Diode Modules 20 Amperes/300-600 Volts |
| CC2403020N | 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Super Fast Recovery Dual Diode Modules 20 Amperes/300-600 Volts |
| CC2403500N | 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Super Fast Recovery Dual Diode Modules 50 Amperes/300-600 Volts |
| CC-2404K2A-CS | 功能描述:MODEM 2400BAUD SERIAL 3.3V RoHS:否 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:- 標準包裝:25 系列:- 數據格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
發(fā)布緊急采購，3分鐘左右您將得到回復。