CC-2401K2 Page 14 of 66 2007, Copeland Communications, Inc. CC-2401K2 Datasheet Rev 1.5 The host then sends the ATRO command to the CC" />
參數資料
型號： CC-2401K2A-CS
廠商： Copeland Communications Inc
文件頁數： 6/66頁
文件大小： 0K
描述： MODEM 2400BAUD SECURE 3.3V
標準包裝： 30
數據格式： V.21，V.22，V.23，Bell 103
波特率： 2.4k
電源電壓： 3 V ~ 3.6 V
安裝類型： 表面貼裝
封裝/外殼： 模塊
包裝： 散裝
配用： 539-1002-ND - KIT EVALUATION WORLD MODEM II
其它名稱： 539-1010
CC-2401K2A-CS-ND
Data Sheet
CC-2401K2
Page 14 of 66
2007, Copeland Communications, Inc.
CC-2401K2 Datasheet Rev 1.5
The host then sends the ATRO command to the CC-2401 to initiate a V.23 turnaround and return to online
data mode.
The CC-2401 then changes its carrier frequency from 390 Hz to 1300 Hz) and wait to detect a 390 Hz
carrier for 440 ms. If the modem detects more than 40 ms of a 390 Hz carrier in a time window of 440 ms,
it echoes the “c” response. If the modem does not detect more than 40 ms of a 390 Hz carrier in a time
window of 440 ms, it hangs up and echoes the “N” (no carrier) character as a response.
Modem in Slave Mode
Enable Slave mode by configuring GPIO4 and INT# (SE2[7:6][GPIO4] = 11). The CC-2401 performs a
reverse turnaround when it detects a carrier drop longer than 20 ms. The CC-2401 then reverses and
waits to detect a 1300 Hz carrier for 400 ms. If the CC-2401 detects more than 40 ms of a 1300 Hz
carrier in a time window of 400 ms, it sets the S09[7] bit and the next character echoed by the CC-2401 is
a “v”.
If the CC-2401 doe not detect more than 40 ms of the 1300 Hz carrier in a time window of 400 ms, it
reverses again and waits to detect a 390 Hz carrier for 440 ms. Then if the CC-2401 detects more than
40 ms of a 390 Hz carrier in a time window of 220 ms, it sets the S09[7] bit, and the CC-2401 echoes a
“c”.
At this point, if the CC-2401 does not detect more than 40 ms of the 390 Hz carrier in a time window of
440 ms, it hangs up, sets the S09[7] bit, and the CC-2401 echoes a “N” (no carrier).
Successful completion of a turnaround procedure in master or slave mode automatically updates
S07[4](V23T) and S07[5] (V23R) to indicate the new status of the V.23 connection.
To avoid using the INT# pin, the host may also be notified of the INT# condition using the 9-bit data mode.
Setting S15[0] (NBE) = 1 and S0C[3] (9BF) = 0b configures the ninth bit on the CC-2401 TXD path to
function exactly as the INT# pin has been described.
V.42 HDLC Operation
The CC-2401 supports V.42 through hardware HDLC framing in all modem data modes. Frame packing and
unpacking including opening and closing flag generation and detection, CRC computation and checking, zero
insertion and deletion, and modem data transmission and reception are all performed by the CC-2401. V.42
error correction and V.42bis data compression must be performed by the host.
The digital link interface in this mode uses the same UART interface (8-bit data mode and 9-bit data formats)
as in the asynchronous modes, and the ninth data bit may be used as an escape by setting S15[0](NBE) = 1.
When using HDLC in 9-bit data mode, if the ninth bit is not used as an escape, it is ignored.
To use the HDLC feature on the CC-2401, the host must enable HDLC operation by setting S13[1](HDEN) = 1.
The host may initiate the call or answer the call using either the “ATDT#”, the “ATA” command or the auto
answer mode. Auto answer mode is implemented by setting register S00 (NR) to a non-zero value. When the
call is connected, a “c”, “d” or a “v” result is echoed to the host controller. The host may now send and receive
data across the UART using either the 8 or 9 bit data formats with flow control.
Once in this state, the CC-2401 begins framing data into the HDLC format.
On the transmit side, if no data is
available from the host, the HDLC flag pattern is sent repeatedly.
When data is available, the CC-2401
computes the CRC code throughout the frame, and the data is sent with the HDLC zero-bit insertion algorithm.
HDLC flow control operates in a similar manner to normal asynchronous flow control across the UART. To
operate flow control using the CTS pin to indicate when the CC-2401 is ready to accept a character, a DTE
rate higher than the line rate should be selected. The method of transmitting HDLC frames is as follows:
1.
After the call is connected, the host should begin sending the frame data to the CC-2401 using the CTS#
flow control to ensure data synchronicity.
相關PDF資料
PDF描述
CC-2434K2-CS5 MODEM FAX 33K 5V
CC-24K2N-CS5 MODEM WORLD NET 2400BAUD 5V
CC-92K2-IS MODEM 56KBAUD V.90 SERIAL 3.3V
CC-MX-LB69-ZM CONNECTCORE I.MX51 MODULE
CD22M3494MQZ96 IC CROSSPOINT SWITCH 16X8 44PLCC
相關代理商/技術參數
參數描述
CC-2401K2A-CS5 功能描述:MODEM 2400BAUD SECURE 5V RoHS:否 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:- 標準包裝:25 系列:- 數據格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574
CC24020N 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Super Fast Recovery Dual Diode Modules 20 Amperes/300-600 Volts
CC2403020N 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Super Fast Recovery Dual Diode Modules 20 Amperes/300-600 Volts
CC2403500N 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Super Fast Recovery Dual Diode Modules 50 Amperes/300-600 Volts
CC-2404K2A-CS 功能描述:MODEM 2400BAUD SERIAL 3.3V RoHS:否 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:- 標準包裝:25 系列:- 數據格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*