CC-2401K2 Page 15 of 66 2007, Copeland Communications, Inc. CC-2401K2 Datasheet Rev 1.5 2. When the frame is complete, the host should" />
參數資料
型號： CC-2401K2A-CS
廠商： Copeland Communications Inc
文件頁數： 7/66頁
文件大?。?/td> 0K
描述： MODEM 2400BAUD SECURE 3.3V
標準包裝： 30
數據格式： V.21，V.22，V.23，Bell 103
波特率： 2.4k
電源電壓： 3 V ~ 3.6 V
安裝類型： 表面貼裝
封裝/外殼： 模塊
包裝： 散裝
配用： 539-1002-ND - KIT EVALUATION WORLD MODEM II
其它名稱： 539-1010
CC-2401K2A-CS-ND
Data Sheet
CC-2401K2
Page 15 of 66
2007, Copeland Communications, Inc.
CC-2401K2 Datasheet Rev 1.5
2.
When the frame is complete, the host should simply stop sending data to the CC-2401. Since the CC-
2401 does not yet recognize the end of frame, it expects an extra byte and asserts CTS. If CTS is used to
cause a host interrupt, this final interrupt should be ignored by the host.
3.
When the CC-2401 is ready to send the next byte, if it has not yet received any data from the host, it
recognizes this as an end of frame, raises CTS, calculates the final CRC code, transmits the code and
begins transmitting stop flags.
4.
After transmitting the first stop flag, the CC-2401 lowers CTS indicating that it is ready to receive the next
frame from the host. At this point, the process begins again at step 1.
The method for receiving HDLC frames follows:
1.
After the call is connected, the CC-2401 searches for flag data. Once the first non flag word is detected,
the CRC is continuously computed and the data is sent across the UART to the host after removing the
HDLC zero-bit insertion. The DTE rate of the host must be at least as high as that of data transmission.
HDLC mode only works with 8 bit data words; the ninth bit is used only for escape on TXD and end of
frame received (EOFR) on RXD.
2.
When the CC-2401 detects the stop flag, it sends the last data word in the frame as well as the two CRC
bytes and determine if the CRC checksum matches. Thus, the last two bytes are not frame data but are
the CRC bytes, which can be discarded by the host. If the checksum matches, the CC-2401 sends “G”
(good). If the checksum does not match, the CC-2401 sends “e” (error). In addition, if the CC-2401
detects an abort (seven or more contiguous ones), it sends an “A”. When the “G”, “e”, or “A” (referred to
as a frame result word) is sent, the CC-2401 raises the EOFR (end of frame receive) pin. The GPIO1 pin
must be configured as EOFR by setting SE4[3](GPE) = 1. In addition to using the EOFR pin to indicate
that the byte is a frame result word, if in 9 bit data mode, (set S15[0] (NBE) = 1), the ninth bit is raised if
the byte is a frame result word. To program this mode, set S0C[3] (9BF) = 1 and SE0[3] (ND) = 1.
3.
When the next frame of data is detected, EOFR is lowered and the process repeats with step 1.
When receiving HDLC frames, the host begins receiving data asynchronously from the CC-2401. When each
byte is received, the host should check the EOFR pin (or the ninth data bit). If the EOFR pin (or ninth data bit)
is low, the data is valid frame data. If the EOFR pin (or ninth bit) is high, the data is a frame result word.
Fast Connect
In modem applications that require fast connection times, it is possible to reduce the length of the handshake.
Additional modem handshaking control can be adjusted through the registers shown in the following table.
These registers are most useful if the user has control of both the originating and answering modems. When
the fast connect settings are used, there may be unintended data received initially. The host must tolerate
these bytes.
Register
Name
Function
Units
Default
Fast
Connect
S1E
TATL
Transmit Answer Tone Length
1 s
0x03
00
S1F
ATTD
Answer Ton to Transmit Delay
5/3 ms
0x2D
00
S20
UNL
Unscrambled Ones Length-V.22
5/3 ms
0x5D
00
S21
TSOD
Transmit Scrambled Ones Delay – V.22
53.3 ms
0x09
00
S22
TSOL
Transmit Scrambled Ones Length – V.22
5/3 ms
0xA2
00
S23
VDDL
V.22/22b Data Delay Low
5/3 ms
0xCB
00
S24
VDDH
V.22/22b Data Delay High
(256) 5/3 ms
0x08
00
S34
TASL
Answer Tone Length
(only used in S1E[TATL] = 0x00)
5/3 ms
0x5A
F0
S35
RSOL
Receive V.22 Scrambled Ones Length
5/3 ms
0xA2
00
相關PDF資料
PDF描述
CC-2434K2-CS5 MODEM FAX 33K 5V
CC-24K2N-CS5 MODEM WORLD NET 2400BAUD 5V
CC-92K2-IS MODEM 56KBAUD V.90 SERIAL 3.3V
CC-MX-LB69-ZM CONNECTCORE I.MX51 MODULE
CD22M3494MQZ96 IC CROSSPOINT SWITCH 16X8 44PLCC
相關代理商/技術參數
參數描述
CC-2401K2A-CS5 功能描述:MODEM 2400BAUD SECURE 5V RoHS:否 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:- 標準包裝:25 系列:- 數據格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574
CC24020N 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Super Fast Recovery Dual Diode Modules 20 Amperes/300-600 Volts
CC2403020N 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Super Fast Recovery Dual Diode Modules 20 Amperes/300-600 Volts
CC2403500N 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Super Fast Recovery Dual Diode Modules 50 Amperes/300-600 Volts
CC-2404K2A-CS 功能描述:MODEM 2400BAUD SERIAL 3.3V RoHS:否 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:- 標準包裝:25 系列:- 數據格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*