- 您現在的位置：買賣IC網 > PDF目錄1908 > CP82C50A-5Z (Intersil)IC ASYNC COMM ELEMENT UART 40DIP PDF資料下載
參數資料
| 型號： | CP82C50A-5Z |
| 廠商： | Intersil |
| 文件頁數： | 20/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ASYNC COMM ELEMENT UART 40DIP |
| 標準包裝： | 9 |
| 特點： | 單芯片 UART/BRG |
| 通道數： | 1，UART |
| 規程： | RS232C |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 帶并行端口： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 40-DIP（0.600"，15.24mm） |
| 供應商設備封裝： | 40-DIP |
| 包裝： | 管件 |
4
FN2958.5
August 24, 2006
82C50A
Pin Description
SYMBOL
PIN
NUMBER
TYPE
ACTIVE
LEVEL
DESCRIPTION
DISTR,
DISTR
22
21
I
H
L
DATA IN STROBE, DATA IN STROBE: DISTR, DISTR are read inputs which cause the
82C50A to output data to the data bus (D0-D7). The data output depends upon the
register selected by the address inputs A0, A1, A2. The chip select inputs CS0, CS1,
CS2 enable the DISTR, DISTR inputs.
Only an active DISTR or DISTR, not both, is used to receive data from the 82C50A
during a read operation. If DISTR is used as the read input, DlSTR should be tied high.
If DISTR is used as the active read input, DISTR should be tied low.
DOSTR,
DOSTR
19
18
I
H
L
DATA OUT STROBE, DATA OUT STROBE: DOSTR, DOSTR are write inputs which
cause data from the data bus (D0-D7) to be input to the 82C50A. The data input depends
upon the register selected by the address inputs A0, A1, A2. The chip select inputs CS0,
CS1, CS2 enable the DOSTR, DOSTR inputs.
Only an active DOSTR or DOSTR, not both, is used to transmit data to the 82C50A
during a write operation. If DOSTR is used as the write input, DOSTR should be tied
high. If DOSTR is used as the write input, DOSTR should be tied low.
D0-D7
1-8
I/O
DATA BITS 0-7: The Data Bus provides eight, three-state input/output lines for the
transfer of data, control and status information between the 82C50A and the CPU. For
character formats of less than 8 bits, D7, D6 and D5 are “don’t cares” for data write
operations and 0 for data read operations. These lines are normally in a high impedance
state except during read operations. D0 is the Least Significant Bit (LSB) and is the first
serial data bit to be received or transmitted.
A0, A1,
A2
28, 27,
26
I
H
REGISTER SELECT: The address lines select the internal registers during CPU bus
operations. See Table 1.
XTAL1,
XTAL2
16
17
I
O
CRYSTAL/CLOCK: Crystal connections for the internal Baud Rate Generator. XTAL1
can also be used as an external clock input, in which case XTAL2 should be left open.
SOUT
11
O
SERIAL DATA OUTPUT: Serial data output from the 82C50A transmitter circuitry. A
Mark (1) is a logic one (high) and Space (0) is a logic zero (low). SOUT is held in the
Mark condition when the transmitter is disabled, MR is true, the Transmitter Register is
empty, or when in the Loop Mode. SOUT is not affected by the CTS input.
GND
20
L
GROUND: Power supply ground connection (VSS).
CTS
36
I
L
CLEAR TO SEND: The logical state of the CTS pin is reflected in the CTS bit of the
(MSR) Modem Status Register (CTS is bit 4 of the MSR, written MSR (4)). A change of
state in the CTS pin since the previous reading of the MSR causes the setting of DCTS
(MSR(O)) of the Modem Status Register. When CTS pin is ACTIVE (low), the modem is
indicating that data on SOUT can be transmitted on the communications link. If CTS pin
goes INACTIVE (high), the 82C50A should not be allowed to transmit data out of SOUT.
CTS pin does not affect Loop Mode operation.
DSR
37
I
L
DATA SET READY: The logical state of the DSR pin is reflected in MSR(5) of the
Modem Status Register. DDSR (MSR(1)) indicates whether the DSR pin has changed
state since the previous reading of the MSR. When the DSR pin is ACTIVE (low), the
modem is indicating that it is ready to exchange data with the 82C50A, while the DSR
Pin INACTIVE (high) indicates that the modem is not ready for data exchange. The
ACTIVE condition indicates only the condition of the local Data Communications
Equipment (DCE), and does not imply that a data circuit as been established with remote
equipment.
DTR
33
O
L
DATA TERMINAL READY: The DTR pin can be set (low) by writing a logic 1 to MCR(0),
Modem Control Register bit 0. This signal is cleared (high) by writing a logic 0 to the DTR
bit (MCR(0)) or whenever a MR ACTIVE (high) is applied to the 82C50A. When ACTIVE
(low), DTR pin indicates to the DCE that the 82C50A is ready to receive data. In some
instances, DTR pin is used as a power on indicator. The INACTIVE (high) state causes
the DCE to disconnect the modem from the telecommunications circuit.
RTS
32
O
L
REQUEST TO SEND: The RTS signal is an output used to enable the modem. The RTS
pin is set low by writing a logic 1 to MCR (1) bit 1 of the Modem Control Register. The
RTS pin is reset high by Master Reset. When ACTIVE, the RTS pin indicates to the DCE
that the 82C50A has data ready to transmit. In half duplex operations, RTS is used to
control the direction of the line.
BAUDOUT
15
O
BAUDOUT: This output is a 16X clock out used for the transmitter section (16X = 16
times the data rate). The BAUDOUT clock rate is equal to the reference oscillator
frequency divided by the specified divisor in the Baud Rate Generator Divisor Latches
DLL and DLM. BAUDOUT may be used by the Receiver section by tying this output to
RCLK.
相關PDF資料 |
PDF描述 |
|---|---|
| CP82C89 | IC ARBITER BUS 5V 8MHZ 20-DIP |
| CPC1465D | IC DC TERMINATION 16-SOIC |
| CPC1465M | IC SHDSL/ISDN DC TERM 16MLP |
| CPC2400E | MODULE MODEM 2400BAUD EMBEDDEDED |
| CPC5601D | IC DRVR PROGRAMMABLE 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CP82C52 | 功能描述:UART 接口集成電路 PERIPH UART/BRG 5V 16MHZ 28PDIP COM RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| CP82C52Z | 功能描述:UART 接口集成電路 PERIPH UART/BRG 5V 16MHZ COM /ANNEAL RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| CP82C54 | 功能描述:計時器和支持產品 PERIPH PRG-CNTR 5V 8MHZ 24PDIP COM RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| CP82C5410 | 制造商:Harris Corporation 功能描述: |
| CP82C54-10 | 功能描述:計時器和支持產品 PERIPH PRG-CNTR 5V 10MHZ 24PDIP COM RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。