參數資料
型號： CP82C50A-5Z
廠商： Intersil
文件頁數： 21/25頁
文件大?。?/td> 0K
描述： IC ASYNC COMM ELEMENT UART 40DIP
標準包裝： 9
特點： 單芯片 UART/BRG
通道數： 1，UART
規程： RS232C
電源電壓： 4.5 V ~ 5.5 V
帶并行端口： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 通孔
封裝/外殼： 40-DIP（0.600"，15.24mm）
供應商設備封裝： 40-DIP
包裝： 管件
5
FN2958.5
August 24, 2006
82C50A
OUT1
34
O
L
OUTPUT 1: This is a general purpose output that can be programmed ACTIVE (low) by
settingVCR(2) (OUT1) of the Modem Control Register to a high level. The OUT1 pin is
set high by Master Reset. The OUT1 pin is INACTIVE (high) during loop mode operation.
OUT2
31
O
L
OUTPUT 2: This is a general purpose output that can be programmed ACTIVE (low) by
setting MCR(3) (OUT1) of the Modem Control Register to a high level. The OUT2 pin is
set high by Master Reset. The OUT2 signal is INACTIVE (high) during loop mode
operation.
RI
39
1
L
RING INDICATOR: When low, RI indicates that a telephone ringing signal has been
received by the modem or data set. The RI signal is a modem control input whose
condition is tested by reading MSR(6) (RI). The Modem Status Register output TERI
(MSR(2)) indicates whether the RI input has changed from a Low to High since the
previous reading of the MSR. If the interrupt is enabled (IER (3) = 1) and RI changes from
a Low to High, an interrupt is generated. The ACTIVE (low) state of RI indicates that the
DCE is receiving a ringing signal. RI will appear ACTIVE for approximately the same
length of time as the ACTIVE segment of the ringing cycle. The INACTIVE state of RI will
occur during the INACTIVE segments not detected by the DCE. This circuit is not
disabled by the INACTIVE condition of DTR.
DCD
38
I
L
DATA CARRIER DETECT: When ACTIVE (low), DCD indicates that the data carrier has
been detected by the modem or data set. DCD is a modem input whose condition can
be tested by the CPU by reading MSR(7) (DCD) of the Modem Status Register. MSR(3)
(DDCD) of the Modem Status Register indicates whether the DCD input has changed
since the previous reading of the MSR. DOD has no effect on the receiver. If the DCD
changes state with the modem status interrupt enabled, an interrupt is generated.
When DCD is ACTIVE (low), the received line signal from the remote terminal is within
the limits specified by the DCE manufacturer. The INACTIVE (high) signal indicates that
the signal is not within the specified limits, or is not present.
MR
35
1
H
MASTER RESET: The MR input forces the 82C50A into an idle mode in which all serial
data activities are suspended. The Modem Control Register (MCR) along with its
associated outputs are cleared. The Line Status Register (LSR) is cleared except for the
THRE and TEMT bits, which are set. The 82C50A remains in an idle state until
programmed to resume serial data activities. The MR input is a Schmitt trigger input. See
the DC Electrical Characteristics for Schmitt trigger logic input voltage levels. See Table
7 for a summary of Master Reset’s effect on 82C50A operation.
lNTRPT
30
O
H
INTERRUPT REQUEST: The lNTRPT output goes ACTIVE (high) when one of the
following interrupts has an ACTIVE (high) condition and is enabled by the Interrupt
Enable Register: Receiver Error flag, Received Data Available, Transmitter Holding
Register Empty, and Modem Status. The lNTRPT is reset low upon appropriate service
or a MR operation. See Figure 1. Interrupt Control Structure.
SIN
10
I
H
SERIAL DATA INPUT: The SIN input is the serial data input from the communication line
or modem to the 82C50A receiver circuits. A mark (1) is high, and a space (0) is low. Data
inputs on SIN are disabled when operating in the loop mode.
VCC
40
H
VCC: +5V positive power supply pin. A 0.1μA decoupling capacitor from VCC (pin 40)
to GND (pin 20) is recommended.
CS0, CS1,
CS2
12,13,
14
I
H, H,
L
CHIP SELECT: The Chip Select inputs act as enable signals for the write (DOSTR,
DOSTR) and read (DlSTR, DlSTR) input signals. The Chip Select inputs are latched by
the ADS input.
NC
29
Do Not Connect
CSOUT
24
O
H
CHIP SELECT OUT: When ACTIVE (high), this pin indicates that the chip has been
selected by active CS0, CS1, and CS2 inputs. No data transfer can be initiated until
CSOUT is a logic 1, ACTIVE (high).
DDIS
23
O
H
DRIVER DISABLE: This output is INACTIVE (low) when the CPU is reading data from
the 82C50A. An ACTIVE (high) Dells output can be used to disable an external
transceiver when the CPU is reading data.
ADS
25
I
L
ADDRESS STROBE: When ACTIVE (low), ADS latches the Register Select (A0, A1,
A2) and Chip Select (CS0, CS1, CS2) inputs. An active ADS is required when the
Register Select pins are not stable for the duration of the read or write operation,
multiplexed mode. If not required, the ADS input should be tied low, non-multiplexed
mode.
RCLK
9
I
This input is the 16X Baud Rate Clock for the receiver section of the 82C50A. This input
may be provided from the BAUDOUT output or an external clock.
Pin Description (Continued)
SYMBOL
PIN
NUMBER
TYPE
ACTIVE
LEVEL
DESCRIPTION
相關PDF資料
PDF描述
CP82C89 IC ARBITER BUS 5V 8MHZ 20-DIP
CPC1465D IC DC TERMINATION 16-SOIC
CPC1465M IC SHDSL/ISDN DC TERM 16MLP
CPC2400E MODULE MODEM 2400BAUD EMBEDDEDED
CPC5601D IC DRVR PROGRAMMABLE 16-SOIC
相關代理商/技術參數
參數描述
CP82C52 功能描述:UART 接口集成電路 PERIPH UART/BRG 5V 16MHZ 28PDIP COM RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
CP82C52Z 功能描述:UART 接口集成電路 PERIPH UART/BRG 5V 16MHZ COM /ANNEAL RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
CP82C54 功能描述:計時器和支持產品 PERIPH PRG-CNTR 5V 8MHZ 24PDIP COM RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel
CP82C5410 制造商:Harris Corporation 功能描述:
CP82C54-10 功能描述:計時器和支持產品 PERIPH PRG-CNTR 5V 10MHZ 24PDIP COM RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*