參數資料
型號： CR16HCT9VJE7Y
英文描述： Microcontroller
中文描述： 微控制器
文件頁數： 42/157頁
文件大?。?/td> 1256K
代理商： CR16HCT9VJE7Y
www.national.com
42
13.0
Multi-Input Wake-Up
The Multi-Input Wake-Up (MIWU16) module monitors its 16
input channels for a software-selectable trigger condition.
Upon detection of a trigger condition, the module generates
an interrupt request and if enabled, a wake-up request. A
wake-up request can be used by the power management unit
to exit the Halt, Idle, or Power Save mode and return to the
active mode. An interrupt request generates an interrupt to
the CPU (interrupt IRQ2), allowing interrupt processing in re-
sponse to external events.
The wake-up event only activates the clocks and CPU, but
does not by itself initiate execution of any code. It is the inter-
rupt request associated with the MIWU16 that gets the CPU
to start executing code, by jumping to the proper interrupt
routine. Therefore, setting up the MIWU16 interrupt handler
is essential for any wake-up operation.
There are four interrupt requests that can be routed to the
ICU as shown in Figure 9. Each of the 16 MIWU channels
can be programmed to activate one of these four interrupt re-
quests.
The input pins for the Multi-Input Wake-Up channels are
named WUI0 through WUI15.
WUI0
WUI1
WUI2
WUI3
WUI4
WUI5
WUI6
WUI7
WUI8
WUI9
WUI10
WUI11
WUI12
WUI13
WUI14
WUI15
Each input can be configured to trigger on rising or falling
edges, as determined by the setting in the WKEDG register.
Each trigger event is latched into the WKPND register. If a
trigger event is enabled by its respective bit in the WKENA
register, an active wake-up/interrupt signal is generated. The
software can determine which channel has generated the ac-
tive signal by reading the WKPND register.
The Multi-Input Wake-Up module is active at all times, includ-
ing the Halt mode. All device clocks are stopped in this mode.
Therefore, detecting an external trigger condition and the
subsequent setting of the pending flag are not synchronous
to the system clock.
13.1
WAKE-UP EDGE DETECTION REGISTER
(WKEDG)
The Wake-Up Edge Detection (WKEDG) register is a word-
wide read/write register that controls the edge sensitivity of
the Multi-Input Wake-Up pins. Register bits 0 through 15 con-
trol input pins WUI0 through WUI15, respectively. A bit
cleared to 0 configures the corresponding input to trigger on
a rising edge (a low-to-high transition). A bit set to 1 config-
ures the corresponding input to trigger on a falling edge (a
high-to-low transition).
This register is cleared upon reset, which configures all 16 in-
puts to be triggered on rising edges.
The register format is shown below.
15
WKED15-WKED0
13.2
The Wake-Up Enable (WKENA) register is a word-wide read/
write register that enables or disables each of the Multi-Input
Wake-Up channels. Register bits 0 through 15 control chan-
nels WUI0 through WUI15, respectively. A bit cleared to 0
disables the wake-up function and a bit set to 1 enables the
function.
This register is cleared upon reset, which disables all eight
wake-up/interrupt channels.
WAKE-UP ENABLE REGISTER (WKENA)
PL0
PL1
PL2
PL3
PH0
PH1
PH2
PH3
TWM-T0OUT
ACCESS.bus
Canards
MWCS
RDX1
RDX2
Comparator 1
Comparator 2
0
相關PDF資料
PDF描述
CR16HCT9VJE8 Microcontroller
CR16HCT9VJE8Y Microcontroller
CR16HCT9VJE9 Microcontroller
CR16HCT9VJE9Y Microcontroller
CR16MCT5VJE8Y Microcontroller
相關代理商/技術參數
參數描述
CR16HCT9VJE8 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller
CR16HCT9VJE8Y 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller
CR16HCT9VJE9 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller
CR16HCT9VJE9Y 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller
CR16HCT9VJEX 制造商:NSC 制造商全稱:National Semiconductor 功能描述:CR16MCT9/CR16MCT5/CR16HCT9/CR16HCT5 16-Bit Reprogrammable/ROM Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*