參數資料
型號： DDC118
英文描述： Octal Current Input 20-Bit Analog-To-Digital Converter
中文描述： 八路電流輸入20位模擬數字轉換器
文件頁數： 13/30頁
文件大?。?/td> 384K
代理商： DDC118
""#
SBAS325A JUNE 2004 REVISED JUNE 2005
www.ti.com
13
DIGITAL INTERFACE
The digital interface of the DDC118 provides the digital
results via a synchronous serial interface consisting of
differential data clocks (DCLK and DCLK), a valid data pin
(DVALID), differential serial data output pins (DOUT and
DOUT), and differential serial data input pins (DIN and
DIN). The DDC118 contains only four A/D converters, so
the conversion process is interleaved (see Figure 2,
page 9). The integration and conversion processes are
independent of the data retrieval process. Consequently,
the CLK frequency and DCLK frequencies need not be the
same. DIN and DIN are used when multiple converters are
cascaded. Cascading or
daisy-chaining
greatly simplifies
the interconnection and routing of the digital outputs in
cases where a large number of converters are needed.
Refer to the
Cascading Multiple Converters
section of this
data sheet for more detail.
Complementary Signals (DCLK, DIN, and DOUT)
The DDC118 provides optional complementary inputs
(DCLK, DIN) to help reduce digital coupling to the analog
inputs. If using these inputs, connect a complementary
signal to each. If these inputs are not connected on the
DDC118, they should be tied to DGND. DOUT is a
complementary output designed to drive DIN. If not using
DOUT, leave it floating.
System and Data Clocks (CLK and CONV)
The system clock is supplied to CLK and the data clock is
supplied to DCLK. Make sure the clock signals are
clean—avoid overshoot or ringing. For best performance,
generate both clocks from the same clock source. DCLK
should be disabled by taking it low after the data has been
shifted out or while CONV is transitioning.
When using multiple DDC118s, pay close attention to the
DCLK distribution on the printed circuit board (PCB). In
particular, make sure to minimize skew in the DCLK signal
as this can lead to timing violations in the serial interface
specifications. See the
Cascading Multiple Converters
section for more details.
System Clock Divider (CLK_4X)
The CLK_4X input enables an internal divider on the
system clock as shown in Table 3. When CLK_4X = 1, the
system clock is divided by four. This allows a 4X faster
system clock, which in turn provides a finer quantization of
the integration time as the CONV signal needs to be
synchronized with the system clock for the best
performance.
Table 3. CLK_4X Pin Operation
CLK_4X
PIN
CLK DIVIDER
VALUE
TYPICAL CLK
FREQUENCY
INTERNAL CLOCK
FREQUENCY
0
1
4MHz
4MHz
1
4
16MHz
4MHz
High-Speed and Low-Power Modes
(HISPD/LOPWR)
The HISPD/LOPWR input controls the power dissipation
and in turn, the maximum allowable CLK frequency and
data rate, as shown in Table 4. With HISPD/LOPWR = 0,
the Low-Power Mode is selected with a typical 13.5mW/
channel and a maximum data rate of 2.5kSPS. Setting
HISPD/LOPWR = 1 selects the High-Speed Mode, which
supports a maximum data rate of 3.125kSPS with a corre-
sponding typical power of 18.0mW/channel.
Table 4. HISPD/LOPWR Pin Operation
HISPD/
LOPWR
MODE
TYPICAL
POWER/
CHANNEL
MAXIMUM
CLK FREQUENCY
(CLK_4X = 0)
MAXIMUM
DATA
RATE
0
Low-Power
13.5mW/ch
4.0MHz
2.5kSPS
1
High-Speed
18.0mW/ch
4.8MHz
3.125kSPS
Data Valid (DVALID)
The DVALID signal indicates that data is ready. Data
retrieval may begin after DVALID goes low. This signal is
generated using an internal clock divided down from the
system clock CLK. The phase relationship between this
internal clock and CLK is set when power is first applied
and is random. Since the user must synchronize CONV
with CLK, the DVALID signal will have a random phase
relationship with CONV. This uncertainty is
±
1/f
CLK
.
Polling DVALID eliminates any concern about this
relationship. If data read back is timed from CONV, wait the
maximum value of t
7
or t
8
to insure data is valid.
Reset (RESET)
The DDC118 is reset asynchronously by taking the
RESET input low, as shown in Figure 9. Make sure the
reset pulse is at least 50
μ
s wide. After resetting the
DDC118, wait at least four conversions before using the
data. It is very important to make sure the RESET is glitch
free to avoid unintended resets. The RESET pin is used
during power-up; see the
Power-Up Sequence
section for
more details.
RESET
> 50
μ
s
Figure 9. Reset Timing
Convert (CONV)
CONV controls the integration time (T
INT
). For optimum
analog performance, make sure CONV is synchronized to
CLK.
This recommendation implies that while SPEED is low,
T
INT
needs to be adjusted in steps of 250ns if CLK_4X is
low and CLK = 4MHz. If CLK_4X is high and CLK =
16MHz, this allows T
INT
to be adjusted in steps of 62.5ns.
相關PDF資料
PDF描述
DDC118IRTCR Octal Current Input 20-Bit Analog-To-Digital Converter
DDC118IRTCT Octal Current Input 20-Bit Analog-To-Digital Converter
DDG-GJS-K1 LED GaP
DDR-GJS-J2L1-1-I1 LED GaP
DDR-GJS-K1 LED GaP
相關代理商/技術參數
參數描述
DDC118IRTCR 功能描述:模數轉換器 - ADC Octal Current-Input 20-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
DDC118IRTCRG4 功能描述:模數轉換器 - ADC Octal Current-Input 20-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
DDC118IRTCT 功能描述:模數轉換器 - ADC Octal Current-Input 20-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
DDC118IRTCT 制造商:Texas Instruments 功能描述:IC ADC 20BIT OCTAL 48-VQFN
DDC118IRTCT 制造商:Texas Instruments 功能描述:A/D CONVERTER (A-D) IC ((NW))
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*