- 您現在的位置：買賣IC網 > PDF目錄1912 > DP83848CVVX/NOPB (National Semiconductor)TXRX ETHERNET PHYTER 48LQFP PDF資料下載
參數資料
| 型號： | DP83848CVVX/NOPB |
| 廠商： | National Semiconductor |
| 文件頁數： | 13/86頁 |
| 文件大小： | 0K |
| 描述： | TXRX ETHERNET PHYTER 48LQFP |
| 產品培訓模塊： | PHYTER® Family |
| 標準包裝： | 1 |
| 系列： | * |
| 其它名稱： | DP83848CVVX/NOPBDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁
19
www.national.com
DP
83
84
8
C
2.4 LED Interface
The DP83848C supports three configurable Light Emitting
Diode (LED) pins. The device supports three LED configu-
rations: Link, Speed, Activity and Collision. Function are
multiplexed among the LEDs. The PHY Control Register
(PHYCR) for the LEDs can also be selected through
address 19h, bits [6:5].
See Table 3 for LED Mode selection.
The LED_LINK pin in Mode 1 indicates the link status of
the port. In 100BASE-T mode, link is established as a
result of input receive amplitude compliant with the TP-
PMD specifications which will result in internal generation
of signal detect. A 10 Mb/s Link is established as a result of
the reception of at least seven consecutive normal Link
Pulses or the reception of a valid 10BASE-T packet. This
will cause the assertion of LED_LINK. LED_LINK will deas-
sert in accordance with the Link Loss Timer as specified in
the IEEE 802.3 specification.
The LED_LINK pin in Mode 1 will be OFF when no LINK is
present.
The LED_LINK pin in Mode 2 and Mode 3 will be ON to
indicate Link is good and BLINK to indicate activity is
present on either transmit or receive activity.
The LED_SPEED pin indicates 10 or 100 Mb/s data rate of
the port. The standard CMOS driver goes high when oper-
ating in 100 Mb/s operation. The functionality of this LED is
independent of mode selected.
The LED_ACT/COL pin in Mode 1 indicates the presence
of either transmit or receive activity. The LED will be ON for
Activity and OFF for No Activity. In Mode 2, this pin indi-
cates the Collision status of the port. The LED will be ON
for Collision and OFF for No Collision.
The LED_ACT/COL pin in Mode 3 indicates the presence
of Duplex status for 10 Mb/s or 100 Mb/s operation. The
LED will be ON for Full Duplex and OFF for Half Duplex.
In 10 Mb/s half duplex mode, the collision LED is based on
the COL signal.
Since these LED pins are also used as strap options, the
polarity of the LED is dependent on whether the pin is
pulled up or down.
2.4.1 LEDs
Since the Auto-Negotiation (AN) strap options share the
LED output pins, the external components required for
strapping and LED usage must be considered in order to
avoid contention.
Specifically, when the LED outputs are used to drive LEDs
directly, the active state of each output driver is dependent
on the logic level sampled by the corresponding AN input
upon power-up/reset. For example, if a given AN input is
resistively pulled low then the corresponding output will be
configured as an active high driver. Conversely, if a given
AN input is resistively pulled high, then the corresponding
output will be configured as an active low driver.
Refer to Figure 3 for an example of AN connections to
external components. In this example, the AN strapping
results in Auto-Negotiation with 10/100 Half/Full-Duplex
advertised.
The adaptive nature of the LED outputs helps to simplify
potential implementation issues of these dual purpose pins.
Table 3. LED Mode Select
Mode
LED_CFG[1]
(bit 6)
LED_CFG[0]
(bit 5)
or (pin40)
LED_LINK
LED_SPEED
LED_ACT/COL
1
don’t care
1
ON for Good Link
OFF for No Link
ON in 100 Mb/s
OFF in 10 Mb/s
ON for Activity
OFF for No Activity
2
0
ON for Good Link
BLINK for Activity
ON in 100 Mb/s
OFF in 10 Mb/s
ON for Collision
OFF for No Collision
3
1
0
ON for Good Link
BLINK for Activity
ON in 100 Mb/s
OFF in 10 Mb/s
ON for Full Duplex
OFF for Half Duplex
LE
D
_LIN
K
LE
D_SPEED
L
E
D_
ACT/COL
VCC
2.
2
k
11
0
11
0
2.2
k
11
0
AN0 = 1
AN1 = 1
AN_EN = 1
2.
2
k
Figure 3. AN Strapping and LED Loading Example
相關PDF資料 |
PDF描述 |
|---|---|
| DP83848HSQ/NOPB | IC TXRX ETHERNET PHYTER 40-LLP |
| DP83848YB/NOPB | IC TXRX ETHERNET PHYTERA 48-LQFP |
| DRM4000-N00-232 | DRM 4000 MODULE |
| DRM4000L-N00-232 | MODULE DEAD RECKONING RS-232 |
| DS100BR111SQE/NOPB | IC REPEATER 10.3GBPS 2CH 24LLP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DP83848EVV/NOPB | 功能描述:以太網 IC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| DP83848EVVX/NOPB | 功能描述:以太網 IC 10/100 ETHERNET PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| DP83848H | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:DP83848H PHYTER㈢ Mini - Extreme Single 10/100 Ethernet |
| DP83848H_07 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:DP83848H PHYTER㈢ Mini - Extreme Single 10/100 Ethernet |
| DP83848H_08 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:DP83848H PHYTER? Mini - Extreme Single 10/100 Ethernet Transceiver |
發布緊急采購，3分鐘左右您將得到回復。