- 您現在的位置：買賣IC網 > PDF目錄1914 > DS21352LB (Maxim Integrated Products)IC TXRX 1-CHIP T1 3.3V 100-LQFP PDF資料下載
參數資料
| 型號： | DS21352LB |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 93/137頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX 1-CHIP T1 3.3V 100-LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS |
| 產品變化通告： | Product Discontinuation 20/Feb/2012 |
| 標準包裝： | 90 |
| 功能： | 單芯片收發器 |
| 接口： | HDLC，T1 |
| 電路數： | 1 |
| 電源電壓： | 3.14 V ~ 3.47 V |
| 電流 - 電源： | 75mA |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-LQFP（14x14） |
| 包裝： | 托盤 |
| 包括： | DSX-1 和 CSU 線路補償發生器，HDLC 控制器，帶內回路代碼發生器和檢測器 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁當前第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁
DS21352/DS21552
59 of 137
multiframe boundary. In this mode, the elastic store must be enabled however the backplane clock can be
either 1.544 MHz or 2.048 MHz.
If the signaling re–insertion mode is enabled, the user can control which channels have signaling re–
insertion performed on a channel–by–channel basis by setting the RPCSI control bit high (CCR4.6) and
then programming the RCHBLK output pin to go high in the channels in which the signaling re–insertion
should not occur. If the RPCSI bit is set low, then signaling re–insertion will occur in all channels when
the signaling re–insertion mode is enabled (RSRE=1). How to control the operation of the RCHBLK
output pin is covered in Section 13.
10.2.1.2 RECEIVE SIGNALING ALL ONES
In both hardware based signaling operating modes, the user has the option to replace all of the extracted
robbed–bit signaling bit positions with ones. This option is enabled via the RFSA1 control bit (CCR4.5)
and it can be invoked on a per–channel basis by setting the RPCSI control bit (CCR4.6) high and then
programming RCHBLK appropriately just like the per–channel signaling re–insertion operates.
10.2.1.3 RECEIVE SIGNALING FREEZE
The signaling data in the four multiframe buffer will be frozen in a known good state upon either a loss of
synchronization (OOF event), carrier loss, or frame slip. This action meets the requirements of BellCore
TR– TSY–000170 for signaling freezing. To allow this freeze action to occur, the RFE control bit
(CCR4.4) should be set high. The user can force a freeze by setting the RFF control bit (CCR4.3) high.
The RSIGF output pin provides a hardware indication that a freeze is in effect. The four multiframe
buffer provides a three multiframe delay in the signaling bits provided at the RSIG pin (and at the RSER
pin if RSRE=1). When freezing is enabled (RFE=1), the signaling data will be held in the last known
good state until the corrupting error condition subsides. When the error condition subsides, the signaling
data will be held in the old state for at least an additional 9 ms (or 4.5 ms in D4 framing mode) before
being allowed to be updated with new signaling data.
10.2.2 TRANSMIT SIDE
Via the THSE control bit (CCR4.2), the framer can be set up to take the signaling data presented at the
TSIG pin and insert the signaling data into the PCM data stream that is being input at the TSER pin. The
user has the ability to control which channels are to have signaling data from the TSIG pin inserted into
them on a channel–by–channel basis by setting the TPCSI control bit (CCR4.1) high. When TPCSI is
enabled, channels in which the TCHBLK output has been programmed to be set high in, will not have
signaling data from the TSIG pin inserted into them. The signaling insertion capabilities of the framer are
available whether the transmit side elastic store is enabled or disabled. If the elastic store is enabled, the
backplane clock (TSYSCLK) can be either 1.544 MHz or 2.048 MHz.
11. PER–CHANNEL CODE (IDLE) GENERATION
Data can be replaced by an idle code on a channel–by–channel basis in the transmit and receive
directions. The transmit direction is from the backplane to the T1 line and is covered in Section11.1. The
receive direction is from the T1 line to the backplane and is covered in Section 11.2.
相關PDF資料 |
PDF描述 |
|---|---|
| DS21372TN | IC TESTER BIT ERROR 3.3V 32-TQFP |
| DS2141AQN | IC CONTROLLER T1 5V 44-PLCC |
| DS2143QN/T&R | IC CONTROLLER E1 5V LP 44-PLCC |
| DS21448L | IC LIU QUAD E1/T1/J1 128-LQFP |
| DS21455N+ | IC LIU QUAD T1/E1/J1 256-BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS21352LB+ | 功能描述:網絡控制器與處理器 IC T1 Single Chip Transceivers RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21352LBN | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS21352L-C02 | 功能描述:網絡控制器與處理器 IC T1 Single Chip Transceivers RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21352LN | 功能描述:網絡控制器與處理器 IC T1 Single Chip Transceivers RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21352LN+ | 功能描述:網絡控制器與處理器 IC T1 Single Chip Transceivers RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。