參數資料
型號： DS2154LN
廠商： Maxim Integrated Products
文件頁數： 62/87頁
文件大小： 0K
描述： IC TXRX E1 1CHIP 5V ENH 100-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
產品變化通告： Product Discontinuation 20/Feb/2012
標準包裝： 90
類型： 收發器
驅動器/接收器數： 1/1
規程： E1
電源電壓： 4.75 V ~ 5.25 V
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（14x14）
包裝： 管件
DS2154
65 of 87
in Table 13-2. The line driver in the DS2154 contains a current limiter that prevents more than 50mA
(RMS) from being sourced in a 1
load.
Table 13-2. Transformer Specifications
SPECIFICATION
RECOMMENDED VALUE
Turns Ratio
1:1 (receive) and 1:1.15 or 1:1.36 (transmit)
±5%
Primary Inductance
600
H minimum
Leakage Inductance
1.0
H maximum
Intertwining Capacitance
40pF maximum
DC Resistance
1.2
maximum
13.3 Jitter Attenuator
The DS2154 contains an on-board jitter attenuator that can be set to a depth of either 32 or 128 bits via
the JABDS bit in the Line Interface Control Register (LICR). The 128-bit mode is used in applications
where large excursions of wander are expected. The 32-bit mode is used in delay sensitive applications.
The characteristics of the attenuation are shown in Figure 13-4. The jitter attenuator can be placed in
either the receive path or the transmit path by appropriately setting or clearing the JAS bit in the LICR.
Also, the jitter attenuator can be disabled (in effect, removed) by setting the DJA bit in the LICR. In order
for the jitter attenuator to operate properly, a 2.048MHz clock (
±50ppm) must be applied at the MCLK
pin or a crystal with similar characteristics must be applied across the MCLK and XTALD pins. If a
crystal is applied across the MCLK and XTALD pins, then capacitors should be placed from each leg of
the crystal to the local ground plane as shown in Figure 13-1. On-board circuitry adjusts either the
recovered clock from the clock/data recovery block or the clock applied at the TCLKI pin to create a
smooth jitter-free clock that is used to clock data out of the jitter attenuator FIFO. It is acceptable to
provide a gapped/bursty clock at the TCLKI pin if the jitter attenuator is placed on the transmit side. If the
incoming jitter exceeds either 120UIP-P (buffer depth is 128 bits) or 28UIP-P (buffer depth is 32 bits), then
the DS2154 will divide the internal nominal 32.768MHz clock by either 15 or 17 instead of the normal 16
to keep the buffer from overflowing. When the device divides by either 15 or 17, it also sets the Jitter
Attenuator Limit Trip (JALT) bit in the Receive Information Register (RIR.5).
相關PDF資料
PDF描述
M83723/86R8036 CONN PLUG 3POS STRAIGHT W/SCKT
VE-B6W-MY-S CONVERTER MOD DC/DC 5.5V 50W
MS27484E12F35SA CONN PLUG 22POS STRAIGHT W/SCKT
MS3108A36-52S CONN PLUG 52POS RT ANG W/SCKT
VE-B6V-MY-S CONVERTER MOD DC/DC 5.8V 50W
相關代理商/技術參數
參數描述
DS2154LN+ 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2154LNA2 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2154LNA2+ 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2154LND2 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2154LND2+ 制造商:Maxim Integrated Products 功能描述:ENHANCED E1 SCT LQFP REVD2 IND LF - Rail/Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*