- 您現在的位置：買賣IC網 > PDF目錄97867 > DS21Q42T (DALLAS SEMICONDUCTOR) DATACOM, FRAMER, PQFP128 PDF資料下載
參數資料
| 型號： | DS21Q42T |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | Digital Transmission Controller |
| 英文描述： | DATACOM, FRAMER, PQFP128 |
| 封裝： | TQFP-128 |
| 文件頁數： | 75/119頁 |
| 文件大小： | 1309K |
| 代理商： | DS21Q42T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁當前第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁
DS21Q42
59 of 119
13.3 MINIMUM DELAY SYNCHRONOUS RSYSCLK/TSYSCLK MODE
In applications where the framer is connected to backplanes that are frequency locked to the recovered T1
clock (i.e., the RCLK output), the full two frame depth of the onboard elastic stores is really not needed.
In fact, in some delay sensitive applications, the normal two frame depth may be excessive. Register bits
CCR3.7 and CCR3.0 control the RX and TX elastic stores depths. In this mode, RSYSCLK and
TSYSCLK must be tied together and they must be frequency locked to RCLK. All of the slip contention
logic in the framer is disabled (since slips cannot occur). Also, since the buffer depth is no longer two
frames deep, the framer must be set up to source a frame pulse at the RSYNC pin and this output must be
tied to the TSSYNC input. On power–up after the RSYSCLK and TSYSCLK signals have locked to the
RCLK signal, the elastic stores should be reset.
14.
HDLC CONTROLLER
The DS21Q42 has an enhanced HDLC controller configurable for use with the Facilities Data Link or
DS0s. There are 64 byte buffers in both the transmit and receive paths. The user can select any DS0 or
multiple DS0s as well as any specific bits within the DS0(s) to pass through the HDLC controller. See
Figure 20-15 for details on formatting the transmit side. Note that TBOC.6 = 1 and TDC1.7 = 1 cannot
exist without corrupting the data in the FDL. For use with the FDL, see section 15.1. See Table 14-1 for
configuring the transmit HDLC controller.
Four new registers were added for the enhanced functionality of the HDLC controller; RDC1, RDC2,
TDC1, and TDC2. Note that the BOC controller is functional when the HDLC controller is used for
DS0s. Section 15 contains all of the HDLC and BOC registers and information on FDL/Fs Extraction and
Insertion with and without the HDLC controller.
Transmit HDLC Configuration Table 14-1
Function
TBOC.6
TDC1.7
TCR1.2
DS0(s)
0
1
1 or 0
FDL
1
0
1
Disable
0
1 or 0
14.1 HDLC for DS0s
When using the HDLC controllers for DS0s, the same registers shown in section 15 will be used except
for the TBOC and RBOC registers and bits HCR.7, HSR.7, and HIMR.7. As a basic guideline for
interpreting and sending HDLC messages and BOC messages, the following sequences can be applied.
Receive a HDLC Message
1. Enable RPS interrupts
2. Wait for interrupt to occur
3. Disable RPS interrupt and enable either RPE, RNE, or RHALF interrupt
4. Read RHIR to obtain REMPTY status
a. If REMPTY=0, then record OBYTE, CBYTE, and POK bits and then read the FIFO
a1. If CBYTE=0 then skip to step 5
a2. If CBYTE=1 then skip to step 7
b. If REMPTY=1, then skip to step 6
5. Repeat step 4
6. Wait for interrupt, skip to step 4
7. If POK=0, then discard whole packet, if POK=1, accept the packet
8. Disable RPE, RNE, or RHALF interrupt, enable RPS interrupt and return to step 1.
相關PDF資料 |
PDF描述 |
|---|---|
| DS21Q43AT | DATACOM, FRAMER, PQFP128 |
| DS21Q44T | DATACOM, FRAMER, PQFP128 |
| DS21Q44TN | DATACOM, FRAMER, PQFP128 |
| DS21Q48N | DATACOM, PCM TRANSCEIVER, PBGA144 |
| DS21Q48 | DATACOM, PCM TRANSCEIVER, PBGA144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS21Q42T+ | 功能描述:網絡控制器與處理器 IC Enhanced Quad T1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21Q42TN | 功能描述:網絡控制器與處理器 IC Enhanced Quad T1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21Q43A | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Quad E1 Framer |
| DS21Q43AT | 功能描述:網絡控制器與處理器 IC Quad E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21Q43AT+ | 功能描述:網絡控制器與處理器 IC Quad E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。