- 您現在的位置：買賣IC網 > PDF目錄1915 > DS26504LNB2+ (Maxim Integrated Products)IC T1/E1/J1 64KCC ELEMENT 64LQFP PDF資料下載
參數資料
| 型號： | DS26504LNB2+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 54/129頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC T1/E1/J1 64KCC ELEMENT 64LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 160 |
| 功能： | BITS 元件 |
| 接口： | 64KCC，E1，T1 |
| 電路數： | 1 |
| 電源電壓： | 3.14 V ~ 3.47 V |
| 電流 - 電源： | 150mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（10x10） |
| 包裝： | 管件 |
| 包括： | * |
| 其它名稱： | 90-26504+NB2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁當前第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁
DS26504 T1/E1/J1/64KCC BITS Element
30 of 129
7. PROCESSOR INTERFACE
The DS26504 is controlled via a nonmultiplexed (BIS[1:0] = 01) or a multiplexed (BIS[1:0] = 00)
parallel bus. There is also a serial bus mode option, as well as a hardware mode of operation. The bus
interface type is selected by BIS1 and BIS0 as shown in Table 7-1.
Table 7-1. Port Mode Select
BIS1
BIS0
PORT MODE
0
Parallel Port Mode (Multiplexed)
0
1
Parallel Port Mode (Nonmultiplexed)
1
0
Serial Port Mode (SPI)
1
Hardware Mode
7.1 Parallel Port Functional Description
In parallel mode, the DS26504 can operate with either Intel or Motorola bus timing configurations. If the
BTS pin is tied low, Intel timing will be selected; if tied high, Motorola timing will be selected. All
Motorola bus signals are listed in parentheses (). See the timing diagrams in the AC Electrical
Characteristics section for more details.
7.2 SPI Serial Port Interface Functional Description
A serial SPI bus interface is selected when the bus select is 10 (BIS[1:0] = 10). In this mode, a
master/slave relationship is enabled on the serial port with three signal lines (SCK, MOSI, and MISO)
and a chip select (
CS), with the DS26504 acting as the slave. Port read/write timing is not related to the
system read/write timing, thus allowing asynchronous, half-duplex operation. See the AC Electrical
Characteristics section for the AC timing characteristics of the serial port.
7.2.1 Clock Phase and Polarity
Clock Phase and Polarity are selected by the CPHA and CPOL pins. The slave device should always be
configured to match the bus master. See the SPI Serial Port Mode section for detailed functional timing
diagrams.
7.2.2 Bit Order
The most significant bit (MSB) of each byte is transmitted first.
7.2.3 Control Byte
The bus master will transmit two control bytes following a chip select to a slave device. The MSB will be
a R/
W bit (1 = read, 0 = write). The next 6 bits will be padded with zeros. The LSB of the first byte will
be A[7]. The second control byte will be the address bits (A[6:0]) of the target register, followed by a
Burst bit in the LSB position (1 = Burst, 0 = Nonburst).
7.2.4 Burst Mode
The last bit of the second control byte (LSB) is the Burst Mode bit. When the Burst bit is enabled (set to
1) and a read operation is performed, the register address is automatically incremented after the LSB of
the previous byte read to the next register address. Data will be available on the next clock edge following
the LSB of the previous byte read. When the Burst bit is enabled (set to 1) and a write operation is
performed, the register address will be automatically incremented to the next byte boundary following the
LSB of the previous register write, and 8 more data bits will be expected on the serial bus. Burst accesses
相關PDF資料 |
PDF描述 |
|---|---|
| DS26514G+ | IC TXRX T1/E1/J1 4PORT 256-CSBGA |
| DS26518NB1+ | IC TXRX T1/E1/J1 8PORT 256-CSBGA |
| DS26519GN+ | IC TXRX T1/E1/J1 16PRT 484-HSBGA |
| DS26521L+ | IC TXRX T1/E1/J1 64-LQFP |
| DS26522GN+ | IC TXRX T1/E1/J1 DUAL 144CSBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS26504LNB2+ | 功能描述:網絡控制器與處理器 IC E1/T1/J1/64Kcc Bits Element RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS26514 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:4-Port T1/E1/J1 Transceiver Fully Internal Impedance Match, No External Resistor |
| DS26514_11 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:4-Port T1/E1/J1 Transceiver Fully Internal Impedance Match, No External Resistor |
| DS26514DK | 功能描述:網絡開發工具 DS26514 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| DS26514G | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。