參數資料
型號： DS26504LNB2+
廠商： Maxim Integrated Products
文件頁數： 55/129頁
文件大小： 0K
描述： IC T1/E1/J1 64KCC ELEMENT 64LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 160
功能： BITS 元件
接口： 64KCC，E1，T1
電路數： 1
電源電壓： 3.14 V ~ 3.47 V
電流 - 電源： 150mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP（10x10）
包裝： 管件
包括： *
其它名稱： 90-26504+NB2
DS26504 T1/E1/J1/64KCC BITS Element
31 of 129
are terminated when
CS is removed. If CS is removed before all 8 bits of the data are read, the remaining
data will be lost. If
CS is removed before all 8 bits of data are written to the part, no write access will
occur and the target register will not be updated.
Note: During a Burst-Read access, data must be fetched internally to the part as the LSB of the previous
byte is transmitted out. If this pre-fetch read access occurs to a Clear-On-Read register or a FIFO register
address, and the Burst access is terminated without reading this byte out of the port, the data will be lost
and/or the register cleared. Users should not terminate their Burst Read accesses at the address byte
proceeding a Clear-On-Read register or a FIFO register. Data loss could occur due to the internal pre-
fetch operation performed by the interface.
7.2.5 Register Writes
The register write sequence is shown in the functional timing diagrams in Section 18. After a
CS, the bus
master transmits a write control byte containing the R/
W bit, the target register address, and the Burst bit.
These two control bytes will be followed by the data byte to be written. After the first data byte, if the
Burst bit is set, the DS26504 auto-increments its address counter and writes each byte received to the next
higher address location. After writing address FFh, the address counter rolls over to 00h and continues to
auto-increment.
7.2.6 Register Reads
The register read sequence is shown in Section 18. After a
CS, the bus master transmits a read control
byte containing the R/
W bit, the target register address, and the Burst bit. After these two control bytes,
the DS26504 responds with the requested data byte. After the first data byte, if the Burst bit is set, the
DS26504 auto-increments its address counter and transmits the byte stored in the next higher address
location. Note the warning mentioned above, as data loss could potentially occur due to the data pre-fetch
that is required to support this mode. After reading address FFh, the address counter rolls over to 00h and
continues to auto-increment.
相關PDF資料
PDF描述
DS26514G+ IC TXRX T1/E1/J1 4PORT 256-CSBGA
DS26518NB1+ IC TXRX T1/E1/J1 8PORT 256-CSBGA
DS26519GN+ IC TXRX T1/E1/J1 16PRT 484-HSBGA
DS26521L+ IC TXRX T1/E1/J1 64-LQFP
DS26522GN+ IC TXRX T1/E1/J1 DUAL 144CSBGA
相關代理商/技術參數
參數描述
DS26504LNB2+ 功能描述:網絡控制器與處理器 IC E1/T1/J1/64Kcc Bits Element RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS26514 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:4-Port T1/E1/J1 Transceiver Fully Internal Impedance Match, No External Resistor
DS26514_11 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:4-Port T1/E1/J1 Transceiver Fully Internal Impedance Match, No External Resistor
DS26514DK 功能描述:網絡開發工具 DS26514 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
DS26514G 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*