- 您現在的位置：買賣IC網 > PDF目錄1915 > DS3170+ (Maxim Integrated Products)IC TXRX DS3/E3 100-CSBGA PDF資料下載
參數資料
| 型號： | DS3170+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 225/230頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX DS3/E3 100-CSBGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 640 |
| 功能： | 單芯片收發器 |
| 接口： | DS3，E3 |
| 電路數： | 1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 電流 - 電源： | 120mA |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LBGA，CSBGA |
| 供應商設備封裝： | 100-CSBGA（11x11） |
| 包裝： | 托盤 |
| 包括： | DS3 調幀器，E3 調幀器，HDLC 控制器，芯片內 BERT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁當前第225頁第226頁第227頁第228頁第229頁第230頁
DS3170 DS3/E3 Single-Chip Transceiver
94 of 230
The type of BIP-8 error(s) inserted is programmable (errored BIP-8 bit, or errored BIP-8 byte). An errored BIP-8 bit
is inverting a single bit error in the EM byte. An errored BIP-8 byte is inverting all eight bits in the EM byte. BIP-8
error(s) can be inserted one error at a time, or continuously. The BIP-8 error insertion mode (single or continuous)
is programmable.
An REI error is generated by forcing the second bit of the MA byte to a one. REI error(s) can be inserted one error
at a time, or continuously. The REI error insertion mode (single or continuous) is programmable.
Each error type (framing, BIP-8, or REI) has a separate enable. Continuous error insertion mode inserts errors at
every opportunity. Single error insertion mode inserts an error at the next opportunity when requested. The framing
multi-error insertion mode inserts the indicated number of errors at the next opportunities when requested. i.e., a
single request will cause multiple errors to be inserted. The requests can be initiated by a register bit(TSEI) or by
the manual error insertion input (TMEI). The error insertion request source (register or input) is programmable. The
insertion of each particular error type is individually enabled. Once all error insertion has been performed, the data
stream is passed on to overhead insertion.
10.6.8.4 Transmit G.832 E3 Overhead Insertion
Overhead insertion can insert any (or all) of the E3 overhead bytes into the E3 frame. The E3 overhead bytes FA1,
FA2, EM, TR, MA, NR, and GC can be sourced from the transmit overhead interface (TOHCLK, TOH, TOHEN, and
TOHSOF). The EM byte is sourced as an error mask (modulo 2 addition of the input EM byte and the generated
EM byte). The E3 overhead insertion is fully controlled by the transmit overhead interface. If the transmit overhead
data enable signal (TOHEN) is driven high, then the bit on the transmit overhead signal (TOH) is inserted into the
output data stream. Insertion of bits using the TOH signal overwrites internal overhead insertion.
10.6.8.5
Transmit G.832 E3 AIS Generation
G.832 E3 AIS generation overwrites the data stream with AIS. If transmit AIS is enabled, the data stream (payload
and E3 overhead) is forced to all ones.
10.6.8.6 Receive G.832 E3 Frame Processor
The G.832 E3 frame format is shown in Figure 10-17. FA1 and FA2 are the Frame Alignment bytes. EM is the
Error Monitoring byte used for path error monitoring. TR is the Trail Trace byte used for end-to-end connectivity
verification. MA is the Maintenance and Adaptation byte used for far-end path status and performance monitoring
(see Figure 10-18). NR is the Network Operator byte allocated for network operator maintenance purposes. GC is
the General Purpose Communications Channel byte allocated for user communications purposes.
10.6.8.7
Receive G.832 E3 Framing
G.832 E3 framing determines the G.832 E3 frame boundary. The frame boundary is found by identifying the frame
alignment bytes FA1 and FA2, which have a value of F6h and 28h respectively. The framer is an off-line framer
that updates the data path frame counters when an out of frame (OOF) condition has been detected. The use of an
off-line framer reduces the average time required to reframe, and reduces data loss caused by burst error. The
G.832 E3 framer checks each bit position for the frame alignment word (FA1 and FA2). The frame boundary is set
once the frame alignment word is identified. Since, the frame alignment word check is performed one bit at a time,
up to 4296 checks may be needed to find the frame boundary. The data path frame counters are updated if an
error free frame alignment word is received for two additional frames, and an OOF condition is present.
10.6.8.8 Receive G.832 E3 Performance Monitoring
Performance monitoring checks the E3 frame for alarm conditions and errors. The alarm conditions detected are
OOF, LOF, COFA, LOS, AIS, RUA1, and RDI. The errors accumulated are framing, parity, and Remote Error
Indication (REI) errors. An Out Of Frame (OOF) condition is declared when four consecutive frame alignment
words (FA1 and FA2) contain one or more errors, when 986 or more frames out of 1,000 frames has a BIP-8 block
error, or at the next framing word check when a manual reframe is requested. An OOF condition is terminated
when three consecutive frame alignment words (FA1 and FA2) are error free or the G.832 E3 framer updates the
data path frame counters.
A Loss Of Frame (LOF) condition is declared by the LOF integration counter when it has been active for a total of T
ms. The LOF integration counter is active (increments count) when an OOF condition is present, it is inactive (holds
count) when an OOF condition is absent, and it is reset when an OOF condition is absent for T continuous ms. T is
programmable (0, 1, 2, or 3). An LOF condition is terminated when an OOF condition is absent for T continuous
ms.
相關PDF資料 |
PDF描述 |
|---|---|
| DS3172N+ | IC TXRX DS3/E3 DUAL 400-BGA |
| DS3181N+ | IC ATM/PACKET PHY W/LIU 400PBGA |
| DS32512N+ | IC LIU DS3/E3/STS-1 12P 484-BGA |
| DS3254N+ | IC LIU DS3/E3/STS-1 144-CSBGA |
| DS33M33N+ | IC MAPPER ETHERNET 256CSBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3170_11 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:DS3/E3 Single-Chip Transceiver Single-Chip Transceiver for DS3 and E3 |
| DS3170+ | 功能描述:網絡控制器與處理器 IC DS3/E3 Single-Chip Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3170DK | 功能描述:網絡開發工具 DS3170 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| DS3170L | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:DS3/E3 Single-Chip Transceiver |
| DS3170LN | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:DS3/E3 Single-Chip Transceiver |
發布緊急采購，3分鐘左右您將得到回復。