參數資料
型號： DS8007A-EAG+
廠商： Maxim Integrated Products
文件頁數： 11/41頁
文件大?。?/td> 0K
描述： IC INTERFACE SMART CARD 48-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 104
應用： 智能卡
接口： 并聯
電源電壓： 2.7 V ~ 6 V
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 管件
安裝類型： 表面貼裝
DS8007A
Multiprotocol Dual Smart Card Interface
______________________________________________________________________________________
19
UART Control Register 1 (UCR1)
R = unrestricted read, W = unrestricted write, -n = value after reset. This register is reset to 0uuu00uub on RIU = 0.
76
5
4
3
2
1
0
Address 06h
FTE0
FIP
—
PROT
T/R
LCT
SS
CONV
R-0
RW-0
R-0
RW-0
Bit 7: FIFO Threshold Enable 0 (FTE0). When this bit
and the FTE1 (FCR.3) bit are set, the programmable
FIFO threshold feature is enabled. This bit always
reads 0 for compatibility.
Bit 6: Force Inverse Parity (FIP). When this bit is con-
figured to 0, the correct parity is transmitted with each
character, and receive characters are checked for the
correct parity. When FIP = 1, an inverse parity bit is
transmitted with each character and correctly received
characters are NAK’d.
Bit 5: Reserved. This bit must be left 0. Setting this bit
to 1 causes improper device operation.
Bit 4: Protocol Select (PROT). This bit is set to 1 by
software to select the asynchronous T = 1 protocol and
is cleared to 0 to select the T = 0 protocol.
Bit 3: Transmit/Receive (T/R). This bit should be set
by software to operate the UART in transmit mode.
When this bit is changed from 0 to 1 (UART changed
from receive to transmit mode), hardware sets the
USR.RBF/TBE bit, indicating an empty transmit buffer.
The T/R bit is automatically cleared to 0 following suc-
cessful transmission if UCR1.LCT is configured to 1
prior to the transmission. This bit cannot be written to
when RIU = 0 (holding in reset).
Bit 2: Last Character to Transmit (LCT). This bit is
optionally set by software prior to writing the last char-
acter to be transmitted to the UART transmit register
(UTR). If LCT is set to 1 prior to writing to UTR, hard-
ware resets the LCT, T/R, and TBE/RBF bits following a
successful transmission. Setting this bit to 1 allows
automatic change to the reception mode after the last
character is sent. This bit can be set during and before
the transmission. This bit cannot be written to when RIU
= 0 (holding in reset).
Bit 1: Software Convention Setting (SS). This bit
should be set by software prior to ATR to allow automat-
ic convention detection. Hardware automatically resets
the SS bit at 10.5 ETU after the detection of the start bit
of the first character of the ATR.
Bit 0: Convention (CONV). This bit defines the charac-
ter decoding convention of the ISO UART. If CONV = 1,
the convention is direct. If CONV = 0, the convention is
inverted. If automatic convention detection is enabled
(AUTOC = 0), hardware detects the character conven-
tion and configures the CONV bit appropriately at 10.5
ETU. Otherwise (AUTOC = 1), software must configure
the CONV bit.
相關PDF資料
PDF描述
DS8023-RRX+ IC INTERFACE SMART CARD 28-SOIC
DS80C310-ECG IC MCU HI SPEED 25MHZ 44-TQFP
DS80C320-ECL/T&R IC MCU HI SPEED 33MHZ 44-TQFP
DS80C390-FNR IC MPU CAN DUAL HS IND 64-LQFP
DS80C400-FNY IC MCU 75MHZ 16MB HP 100-LQFP
相關代理商/技術參數
參數描述
DS8007A-EAG+ 功能描述:接口 - 專用 Multiprotocol Dual Smart Card Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
DS8007A-EAG+T 功能描述:接口 - 專用 Multiprotocol Dual Smart Card Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
DS8007-ENG 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Multiprotocol Dual Smart Card Interface
DS8007-ENG+ 功能描述:接口 - 專用 Multiprotocol Dual Smart Card Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
DS8007-KIT 功能描述:界面開發工具 DS8007 Eval Kit RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*