參數資料
型號： DS8007A-EAG+
廠商： Maxim Integrated Products
文件頁數： 26/41頁
文件大?。?/td> 0K
描述： IC INTERFACE SMART CARD 48-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 104
應用： 智能卡
接口： 并聯
電源電壓： 2.7 V ~ 6 V
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 管件
安裝類型： 表面貼裝
DS8007A
Multiprotocol Dual Smart Card Interface
32
______________________________________________________________________________________
ISO UART Implementation
Reset Operation
The CSR.RIU control bit resets the ISO UART. The
CSR.RIU must be reset prior to any activation. CSR.RIU
must be returned to 1 by software before any UART
action can take place.
Synchronous Mode
The synchronous mode of operation is invoked by set-
ting the synchronous/asynchronous card select bit (for
a given card interface) to logic 1. In the synchronous
mode of operation, the associated I/Ox card interface
data is transferred by the LSb of the UART
transmit/receive registers (UTR and URR). In this mode,
the host device using the CCRx.SC register bit manual-
ly controls the CLKx pin for the selected card interface.
Switching to the synchronous mode or vice versa is
allowed at any time when the card is active. However, it
is the responsibility of the host software/firmware to
ensure that the current transmission is concluded
before switching. If software configures an active card
for synchronous mode, and then activates another
card, the I/O pin on the previously active card goes to a
high-impedance state with a weak pullup (high). The
newly selected interface (if configured to synchronous
mode) takes on UTR.0.
The AUX card interface does not have an associated
CLK signal, so the CCRAUX.SC bit does not control an
output signal when the synchronous mode of operation
is in effect. The handshake between the host and the
auxiliary smart card interface is accomplished through
the auxiliary interrupt input (INTAUX) and the INT pins.
The MSR.INTAUX bit reflects the state of the INTAUX pin.
If the UCR2.DISAUX bit is cleared to 0, a change on the
INTAUX input pin results in the assertion of INT output
pin. The host software/firmware establishes the commu-
nication protocol and controls when to transmit/receive
data in response to the interrupt. If the UCR2.DISAUX bit
is set to 1, the INT pin is not asserted, and the host soft-
ware/firmware must examine the INTAUX bit in the MSR
register and responds accordingly.
Asynchronous Mode
The asynchronous mode of operation is the reset
default mode for all card interfaces and is selected
when the synchronous/asynchronous card select bit
(for a given card interface) is configured to logic 0. The
I/Ox card interface signal is used for asynchronous
half-duplex data communication between the host-con-
trolled ISO UART and the external smart card. The host
device can optionally stop the CLKx signal in the high
or low state while the card is active using the
CCRx.CST and CCRx.SHL register bits.
ETU Generation and Timing
The basic unit of time for asynchronous mode commu-
nication on the I/Ox signal is the elementary time unit
(ETU). The ETU is defined within the ISO UART as a
function of the fCLK frequency that is configured for the
card interface (i.e., the same fCLK that can be sourced
to the CLKx pin of an associated card interface A or B).
In addition to receiving fCLK from the clock generation
block, the ISO UART additionally receives a 2 x fCLK
frequency if CCRx.AC2–AC0
≠ 000b. The host device
can select whether fCLK or 2 x fCLK is used for ETU
generation by using the clock UART (CKU) select bit.
When CKU = 0, fCLK is used, while 2 x fCLK is used
when CKU = 1. One exception exists when
CCRx.AC2–AC0 = 000b, in which case, only fCLK is
sourced to the UART and the CKU bit setting has no
effect on the duration of an ETU.
The basic clock that is selected for ETU generation by
the CKU bit is further prescaled by a factor or 31 or 32.
The prescaler select control (PSC) bit makes this
prescaler selection. When PSC is configured to logic 0,
the prescale setting is 31. When PSC is configured to
logic 1, the prescale setting is 32. The output of the
clock prescaler drives an 8-bit autoreload down
counter. The autoreload value for the downcounter is
configured by the host device through the
Programmable Divider Register (PDR). The interval pro-
vided by this downcounter defines the ETU duration for
the selected card. Figure 11 shows a diagram of ETU
generation.
All
the
asynchronous
character
transmit/receive operations are defined in terms of ETU
(e.g., 10.5 ETU, 10.25 ETU, etc).
相關PDF資料
PDF描述
DS8023-RRX+ IC INTERFACE SMART CARD 28-SOIC
DS80C310-ECG IC MCU HI SPEED 25MHZ 44-TQFP
DS80C320-ECL/T&R IC MCU HI SPEED 33MHZ 44-TQFP
DS80C390-FNR IC MPU CAN DUAL HS IND 64-LQFP
DS80C400-FNY IC MCU 75MHZ 16MB HP 100-LQFP
相關代理商/技術參數
參數描述
DS8007A-EAG+ 功能描述:接口 - 專用 Multiprotocol Dual Smart Card Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
DS8007A-EAG+T 功能描述:接口 - 專用 Multiprotocol Dual Smart Card Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
DS8007-ENG 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Multiprotocol Dual Smart Card Interface
DS8007-ENG+ 功能描述:接口 - 專用 Multiprotocol Dual Smart Card Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
DS8007-KIT 功能描述:界面開發工具 DS8007 Eval Kit RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*