- 您現在的位置：買賣IC網 > PDF目錄376982 > DS80C390 Dual CAN High-Speed Microprocessor PDF資料下載
參數資料
| 型號： | DS80C390 |
| 英文描述： | Dual CAN High-Speed Microprocessor |
| 中文描述： | 雙CAN高速微處理器 |
| 文件頁數： | 33/58頁 |
| 文件大小： | 5486K |
| 代理商： | DS80C390 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
DS80C390
33 of 58
110199
NOTES FOR DC ELECTRICAL CHARACTERISTICS:
1.
Active current measured with 40 MHz clock source on XTAL1, V
CC
=RST= 5.5 V, all other pins
disconnected.
2.
Idle mode current measured with 40 MHz clock source on XTAL1, V
CC
= 5.5 V, RST=
EA
=V
SS
, all
other pins disconnected.
3.
Stop mode current measured with XTAL1 = RST =
EA
= V
SS
, V
CC
= 5.5 V, all other pins
disconnected. This value is not guaranteed. Users who are sensitive to this specification should
contact Dallas Semiconductor for more information.
4.
When these pins are used to address external memory or as CAN interface signals.
5.
This measurement reflects the port during a 0 to 1 transition in I/O mode. During this period a one-
shot circuit drives the ports hard for two clock cycles.
6.
Port 3 pins 3.6 and 3.7 will have a stronger than normal pullup drive for one oscillator period
following the transition of either the
RD
or
WR
from a 0 to 1 transition.
7.
This is the current required from an external circuit to hold a logic low level on an I/O pin while the
corresponding port latch bit is set to 1. This is only the current required to
hold
the low level;
transitions from 1 to 0 on an I/O pin will also have to overcome the transition current.
8.
Ports 1(in I/O mode), 3, 4, and 5 source transition current when being pulled down externally. It
reaches its maximum at approximately 2V.
9.
During the external addressing mode, weak latches maintain the previously driven value from the
processor on Port 0 until such time that Port 0 is driven by external memory source; and on Port 1, 2
and 4 for one XTAL1 cycle prior to change in output address from Port 1, 2 and 4.
10.
RST= V
CC
. This condition mimics operation of pins in I/O mode.
TYPICAL I
CC
VERSUS FREQUENCY
35
I
CC
mA
30
25
20
15
5
3
2
0 2 4
12
33
40 MHz XTAL
FREQUENCY
相關PDF資料 |
PDF描述 |
|---|---|
| DS80C390-QNR | Dual CAN High-Speed Microprocessor |
| DS80C390-FCR | Dual CAN High-Speed Microprocessor |
| DS80C390-FNR | Dual CAN High-Speed Microprocessor |
| DS80C390-QCR | Dual CAN High-Speed Microprocessor |
| DS80C410 | Network Microcontrollers with Ethernet and CAN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS80C390_00 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Speed Microcontroller User’s Guide Supplement |
| DS80C390_05 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual CAN High-Speed Microprocessor |
| DS80C390+FCR | 制造商:Maxim Integrated Products 功能描述:MICRO DUAL CAN LQFP PB-FREE - Trays |
| DS80C390+QCR | 制造商:Maxim Integrated Products 功能描述:MICRO DUAL CAN PLCC PB-FREE - Rail/Tube |
| DS80C390+QNR | 制造商:Maxim Integrated Products 功能描述:MICRO DUAL CAN PLCC IND PB-FREE - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。