參數資料
型號： DS80C390
英文描述： Dual CAN High-Speed Microprocessor
中文描述： 雙CAN高速微處理器
文件頁數： 7/58頁
文件大?。?/td> 5486K
代理商： DS80C390
DS80C390
7 of 58
110199
80C32 COMPATIBILITY
The DS80C390 is a CMOS 80C32-compatible microcontroller designed for high performance. Every
effort has been made to keep the core device familiar to 80C32 users while adding many new features.
Because the device runs the standard 8051 instruction set, in general software written for existing 80C32-
based systems will work on the DS80C390. The primary exceptions are related to timing-critical issues,
since the high-performance core of the microcontroller executes instructions much faster than the
original. Memory interfacing is performed identically to the standard 80C32. The high-speed nature of
the DS80C390 core will slightly change the interface timing, and designers are advised to consult the
timing diagrams in this data sheet for more information.
The DS80C390 provides the same timer/counter resources, full duplex serial port, 256 bytes of scratchpad
RAM and I/O ports as the standard 80C32. Timers will default to a 12 clocks per machine cycle
operation to keep timing compatible with original 8051 systems, but can be programmed to run at the
faster 4 clocks per machine cycle if desired. New hardware functions are accessed using Special
Function Registers that do not overlap with standard 80C32 locations.
This data sheet provides only a summary and overview of the DS80C390. Detailed descriptions are
available in the corresponding user’s guide. This data sheet assumes a familiarity with the architecture of
the standard 80C32. In addition to the basic features of that device, the DS80C390 incorporates many
new features.
PERFORMANCE OVERVIEW
The DS80C390’s higher performance comes not just from increasing the clock frequency, but from a
more efficient design. This updated core removes the dummy memory cycles that are present in a
standard, 12 clocks per machine cycle 8051. In the DS80C390, the same machine cycle takes 4 clocks.
Thus the fastest instruction, 1 machine cycle, executes 3 times faster for the same crystal frequency. The
majority of instructions on the DS80C390 will see the full 3 to 1 speed improvement, while a few will
execute between 1.5 and 2.4 times faster. Regardless of specific performance improvements, all
instructions are faster than the original 8051.
Improvement of individual programs will depend on the actual mix of instructions used. Speed sensitive
applications should make the most use of instructions that are 3 times faster. However, the large number
of 3 to 1 improved opcodes makes dramatic speed improvements likely for any arbitrary combination of
instructions. These architecture improvements and the sub-micron CMOS design produce a peak
instruction cycle in 100 ns (10 MIPs). The Dual Data Pointer feature also allows the user to eliminate
wasted instructions when moving blocks of memory.
INSTRUCTION SET SUMMARY
All instructions perform exactly the same functions as their 8051 counterparts. Their effect on bits, flags,
and other status functions is identical. However, the timing of instructions is different, both in absolute
and relative number of clocks. The absolute timing of software loops can be calculated using a table in
the user’s guide. However, counter/timers default to run at the traditional 12 clocks per increment. In
this way, timer-based events occur at the standard intervals with software executing at higher speed.
Timers optionally can run at the faster 4 clocks per increment to take advantage of faster processor
operation.
The relative time of two DS80C390 instructions might differ from the traditional 8051. For example, in
the original architecture the “MOVX A, @DPTR” instruction and the “MOV direct, direct” instruction
相關PDF資料
PDF描述
DS80C390-QNR Dual CAN High-Speed Microprocessor
DS80C390-FCR Dual CAN High-Speed Microprocessor
DS80C390-FNR Dual CAN High-Speed Microprocessor
DS80C390-QCR Dual CAN High-Speed Microprocessor
DS80C410 Network Microcontrollers with Ethernet and CAN
相關代理商/技術參數
參數描述
DS80C390_00 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Speed Microcontroller User’s Guide Supplement
DS80C390_05 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual CAN High-Speed Microprocessor
DS80C390+FCR 制造商:Maxim Integrated Products 功能描述:MICRO DUAL CAN LQFP PB-FREE - Trays
DS80C390+QCR 制造商:Maxim Integrated Products 功能描述:MICRO DUAL CAN PLCC PB-FREE - Rail/Tube
DS80C390+QNR 制造商:Maxim Integrated Products 功能描述:MICRO DUAL CAN PLCC IND PB-FREE - Rail/Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*