參數資料
型號: DSP56852VFE
廠商: 飛思卡爾半導體(中國)有限公司
英文描述: 16-bit Digital Signal Controllers
中文描述: 16位數字信號控制器
文件頁數: 26/48頁
文件大?。?/td> 731K
代理商: DSP56852VFE
56852 Technical Data, Rev. 8
26
Freescale Semiconductor
4.7 Reset, Stop, Wait, Mode Select, and Interrupt Timing
Table 4-8 Reset, Stop, Wait, Mode Select, and Interrupt Timing
1,
2
Operating Conditions: V
SS
= V
SSIO
= V
SSA
= 0V, V
DD
= 1.62-1.98V, V
DDIO
= V
DDA
= 3.0–3.6V, T
A
= –40
°
to +120
°
C, C
L
< 50pF, f
op
= 120MHz
1.
In the formulas, T = clock cycle. For f
op
= 120MHz operation and f
ipb
= 60MHz, T = 8.33ns.
Parameters listed are guaranteed by design.
2.
Characteristic
Symbol
Min
Max
Unit
See Figure
RESET Assertion to Address, Data and Control Signals
High Impedance
t
RAZ
11
ns
4-11
Minimum RESET Assertion Duration
3
3.
t
extal
or t
osc
.
4.
The minimum is specified for the duration of an edge-sensitive IRQA interrupt required to recover from the Stop state. This is not
the minimum required so that the IRQA interrupt is accepted.
At reset, the PLL is disabled and bypassed. The part is then put into run mode and t
clk
assumes the period of the source clock, t
xtal
,
t
RA
30
ns
4-11
RESET Deassertion to First External Address Output
t
RDA
120T
ns
4-11
Edge-sensitive Interrupt Request Width
t
IRW
1T + 3
ns
4-12
IRQA, IRQB Assertion to External Data Memory Access
Out Valid, caused by first instruction execution in the
interrupt service routine
t
IDM
18T
ns
4-13
t
IDM -FAST
14T
IRQA, IRQB Assertion to General Purpose Output Valid,
caused by first instruction execution in the interrupt
service routine
t
IG
18T
ns
4-13
t
IG -FAST
14T
IRQA Low to First Valid Interrupt Vector Address Out
recovery from Wait State
4
t
IRI
22T
ns
4-14
t
IRI -FAST
18T
Delay from IRQA Assertion (exiting Stop) to External
Data Memory
5
5.
The interrupt instruction fetch is visible on the pins only in Mode 3.
t
IW
1.5T
ns
4-15
Delay from IRQA Assertion (exiting Wait) to External
Data Memory
Fast
6
Normal
7
6.
Fast stop mode:
Fast stop recovery applies when external clocking is in use (direct clocking to XTAL) or when fast stop mode recovery is requested
(OMR bit 6 is set to 1). In both cases the PLL and the master clock are unaffected by stop mode entry. Recovery takes one less cycle
and t
clk
will continue same value it had before stop mode was entered.
7.
Normal stop mode:
As a power saving feature, normal stop mode disables and bypasses the PLL. Stop mode will then shut down the master clock,
recovery will take an extra cycle (to restart the clock), and t
clk
will resume at the input clock source rate.
8.
ET = External Clock period, For an external crystal frequency of 8MHz, ET=125 ns.
t
IF
18T
22ET
ns
ns
4-15
RSTO pulse width
8
normal operation
internal reset mode
t
RSTO
128ET
8ET
4-16
相關PDF資料
PDF描述
DSP56853E 16-bit Digital Signal Controllers
DSP56853FG120 16-bit Digital Signal Controllers
DSP56853FGE 16-bit Digital Signal Controllers
DSP56854FGE 16-bit Digital Signal Controllers
DSP5685xUM 16-bit Digital Signal Controllers
相關代理商/技術參數
參數描述
DSP56853 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controllers
DSP56853E 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controllers
DSP56853FG120 功能描述:數字信號處理器和控制器 - DSP, DSC 120Mhz/120MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56853FGE 功能描述:數字信號處理器和控制器 - DSP, DSC 120Mhz/120MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56853PB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:56853 Digital Signal Processor Product Brief