參數資料
型號： DSP56F827FG80E
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： 16-bit Digital Signal Controllers
中文描述： 16位數字信號控制器
文件頁數： 14/60頁
文件大小： 811K
代理商： DSP56F827FG80E
56F827 Technical Data, Rev. 12
14
Freescale Semiconductor
RD
15
Output
Read Enable
—RD is asserted during external memory read cycles. When RD
is asserted low, pins D0–D15 become inputs and an external device is
enabled onto the device data bus. When RD is deasserted high, the external
data is latched inside the device. When RD is asserted, it qualifies the
A0–A15, PS, and DS pins. RD can be connected directly to the OE pin of a
Static RAM or ROM.
WR
16
Output
Write Enable
—WR is asserted during external memory write cycles. When
WR is asserted low, pins D0–D15 become outputs and the device puts data on
the bus. When WR is deasserted high, the external data is latched inside the
external device. When WR is asserted, it qualifies the A0–A15, PS, and DS
pins. WR can be connected directly to the WE pin of a Static RAM.
TA0
(GPIOF0)
112
Input/Output
Input/Output
TA0–3
—Timer A Channels 0, 1, 2, and 3
Port F GPIO
—These four General Purpose I/O (GPIO) pins can be
individually programmed as input or output.
After reset, the default state is Quad Timer.
TA1
(GPIOF1)
111
TA2
(GPIOF2)
110
TA3
(GPIOF3)
109
TCK
44
Input
(Schmitt)
Test Clock Input
—This input pin provides a gated clock to synchronize the
test logic and shift serial data to the JTAG/OnCE port. The pin is connected
internally to a pull-down resistor.
TMS
46
Input
(Schmitt)
Test Mode Select Input
—This input pin is used to sequence the JTAG TAP
controller’s state machine. It is sampled on the rising edge of TCK and has an
on-chip pull-up resistor.
Note:
Always tie the TMS pin to V
DD
through a 2.2K resistor.
TDI
48
Input
(Schmitt)
Test Data Input
—This input pin provides a serial input data stream to the
JTAG/OnCE port. It is sampled on the rising edge of TCK and has an on-chip
pull-up resistor.
TDO
47
Input/Output
Test Data Output
—This tri-statable output pin provides a serial output data
stream from the JTAG/OnCE port. It is driven in the Shift-IR and Shift-DR
controller states, and changes on the falling edge of TCK.
TRST
45
Input
(Schmitt)
Test Reset
—As an input, a low signal on this pin provides a reset signal to the
JTAG TAP controller. To ensure complete hardware reset, TRST should be
asserted whenever RESET is asserted. The only exception occurs in a
debugging environment when a hardware device reset is required and it is
necessary not to reset the JTAG/OnCE module. In this case, assert RESET,
but do not assert TRST. TRST must always be asserted at power-up.
Note:
used in a debugging environment, TRST may be tied to V
SS
through a 1K resistor.
For normal operation, connect TRST directly to V
SS
. If the design is to be
DE
41
Output
Debug Event
—DE provides a low pulse on recognized debug events.
Table 2-2 56F827 Signal and Package Information for the 128 Pin LQFP (Continued)
Signal Name
Pin No.
Type
Description
相關PDF資料
PDF描述
DSP56F827 16-bit Hybrid Controller(16位混合控制器)
DSP8-08AC Phase-leg Rectifier Diode ISOPLUS220
DSP8-08 Phase-leg Rectifier Diode
DSP8-08AS Phase-leg Rectifier Diode
DSP8-08S Phase-leg Rectifier Diode
相關代理商/技術參數
參數描述
DSP56F827FG80E 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor IC DSP Type:Cor
DSP56F827FG80E 制造商:Freescale Semiconductor 功能描述:DSP LQFP128 3.6V
DSP56F827PB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:56F827 16-Bit Hybrid Controller Product Brief
DSP56F827PB/D 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:56F827 16-bit Hybrid Controller
DSP56F8XXBLUM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:56F8xx Serial Bootloader User Manual
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*