參數資料
型號： EPM2210F256A4N
廠商： ALTERA CORP
元件分類： PLD
英文描述： FLASH PLD, PBGA256
封裝： 17 X 17 MM, 1 MM PITCH, LEAD FREE, FBGA-256
文件頁數： 51/108頁
文件大?。?/td> 1342K
代理商： EPM2210F256A4N
Altera Corporation
2–39
March 2008
MAX II Device Handbook, Volume 1
MAX II Architecture
Bus Hold
Each MAX II device I/O pin provides an optional bus-hold feature. The
bus-hold circuitry can hold the signal on an I/O pin at its last-driven
state. Since the bus-hold feature holds the last-driven state of the pin until
the next input signal is present, an external pull-up or pull-down resistor
is not necessary to hold a signal level when the bus is tri-stated.
The bus-hold circuitry also pulls undriven pins away from the input
threshold voltage where noise can cause unintended high-frequency
switching. The designer can select this feature individually for each I/O
pin. The bus-hold output will drive no higher than VCCIO to prevent
overdriving signals. If the bus-hold feature is enabled, the device cannot
use the programmable pull-up option.
The bus-hold circuitry uses a resistor to pull the signal level to the last
driven state. The DC and Switching Characteristics chapter in the MAX II
Device Handbook gives the specific sustaining current for each VCCIO
voltage level driven through this resistor and overdrive current used to
identify the next-driven input level.
The bus-hold circuitry is only active after the device has fully initialized.
The bus-hold circuit captures the value on the pin present at the moment
user mode is entered.
Programmable Pull-Up Resistor
Each MAX II device I/O pin provides an optional programmable pull-up
resistor during user mode. If the designer enables this feature for an I/O
pin, the pull-up resistor holds the output to the VCCIO level of the output
pin’s bank.
1
The programmable pull-up resistor feature should not be used
at the same time as the bus-hold feature on a given I/O pin.
Programmable Input Delay
The MAX II IOE includes a programmable input delay that is activated to
ensure zero hold times. A path where a pin directly drives a register, with
minimal routing between the two, may require the delay to ensure zero
hold time. However, a path where a pin drives a register through long
routing or through combinational logic may not require the delay to
achieve a zero hold time. The Quartus II software uses this delay to
ensure zero hold times when needed.
相關PDF資料
PDF描述
EPM2210F256A5N FLASH PLD, PBGA256
EPM2210F324A3N FLASH PLD, PBGA324
EPM2210F324A4N FLASH PLD, PBGA324
EPM2210F324A5N FLASH PLD, PBGA324
EPM2210GF256A3N FLASH PLD, PBGA256
相關代理商/技術參數
參數描述
EPM2210F256A5 功能描述:CPLD - 復雜可編程邏輯器件 CPLD - MAX II 1700 Macro 204 IO RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
EPM2210F256A5N 功能描述:CPLD - 復雜可編程邏輯器件 CPLD - MAX II 1700 Macro 204 IO RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
EPM2210F256C3 功能描述:CPLD - 復雜可編程邏輯器件 CPLD - MAX II 1700 Macro 204 IO RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
EPM2210F256C3N 功能描述:CPLD - 復雜可編程邏輯器件 CPLD - MAX II 1700 Macro 204 IO RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
EPM2210F256C4 功能描述:CPLD - 復雜可編程邏輯器件 CPLD - MAX II 1700 Macro 204 IO RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*