參數資料
型號： EVAL-AD5755-1SDZ
廠商： Analog Devices Inc
文件頁數： 35/52頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD5755-1
視頻文件： AD5755: 16-Bit Multi-Channel, Voltage and Current Output DAC
標準包裝： 1
DAC 的數量： 4
位數： 16
數據接口： 串行
設置時間： 11µs
DAC 型： 電流/電壓
工作溫度： -40°C ~ 105°C
已供物品： 板
已用 IC / 零件： *
AD5755-1
Data Sheet
Rev. E | Page 40 of 52
DEVICE FEATURES
OUTPUT FAULT
The AD5755-1 is equipped with a FAULT pin, an active low
open-drain output allowing several AD5755-1 devices to be
connected together to one pull-up resistor for global fault
detection. The FAULT pin is forced active by any one of the
following fault scenarios:
The voltage at IOUT_x attempts to rise above the compliance
range due to an open-loop circuit or insufficient power
supply voltage. The internal circuitry that develops the
fault output avoids using a comparator with windowed
limits because this requires an actual output error before
the FAULT output becomes active. Instead, the signal is
generated when the internal amplifier in the output stage
has less than approximately 1 V of remaining drive
capability. Thus, the FAULT output activates slightly before
the compliance limit is reached.
A short is detected on a voltage output pin. The short-
circuit current is limited to 16 mA or 8 mA, which is
programmable by the user. If using the AD5755-1 in
unipolar supply mode, a short-circuit fault may be
generated if the output voltage is below 50 mV.
An interface error is detected due to a PEC failure. See the
If the core temperature of the AD5755-1 exceeds
approximately 150°C.
The VOUT_x fault, IOUT_x fault, PEC error, and over TEMP bits
of the status register are used in conjunction with the FAULT
output to inform the user which one of the fault conditions
caused the FAULT output to be activated.
VOLTAGE OUTPUT SHORT-CIRCUIT PROTECTION
Under normal operation, the voltage output sinks/sources up
to 12 mA and maintains specified operation. The maximum
output current or short-circuit current is programmable by
the user and can be set to 16 mA or 8 mA. If a short circuit is
detected, the FAULT goes low and the relevant VOUT_x fault bit
in the status register is set.
DIGITAL OFFSET AND GAIN CONTROL
Each DAC channel has a gain (M) and offset (C) register, which
allow trimming out of the gain and offset errors of the entire
signal chain. Data from the DAC data register is operated on by
a digital multiplier and adder controlled by the contents of the
M and C registers. The calibrated DAC data is then stored in the
DAC input register.
09226-
075
DAC
INPUT
REGISTER
DAC
DAC DATA
REGISTER
M
REGISTER
C
REGISTER
Figure 77. Digital Offset and Gain control
Although Figure 77 indicates a multiplier and adder for each
channel, there is only one multiplier and one adder in the device,
and they are shared among all four channels. This has
implications for the update speed when several channels are
updated at once (see Table 3).
Each time data is written to the M or C register, the output is
not automatically updated. Instead, the next write to the DAC
channel uses these M and C values to perform a new calibration
and automatically updates the channel.
The output data from the calibration is routed to the DAC input
register. This is then loaded to the DAC as described in the
Theory of Operation section. Both the gain register and the
offset register have 16 bits of resolution. The correct method to
calibrate the gain/offset is to first calibrate out the gain and then
calibrate the offset.
The value (in decimal) that is written to the DAC input register
can be calculated by
15
16
2
)
1
(
+
×
=
C
M
D
Code
r
DACRegiste
(1)
where:
D is the code loaded to the DAC channel’s input register.
M is the code in the gain register (default code = 216 – 1).
C is the code in the offset register (default code = 215).
STATUS READBACK DURING A WRITE
The AD5755-1 has the ability to read back the status register
contents during every write sequence. This feature is enabled
via the STATREAD bit in the main control register. This allows
the user to continuously monitor the status register and act
quickly in the case of a fault.
When status readback during a write is enabled, the contents of
the 16-bit status register (see Table 30) are output on the SDO
pin, as shown in Figure 5.
The AD5755-1 powers up with this feature disabled. When this
is enabled, the normal readback feature is not available, except
for the status register. To read back any other register, clear the
STATREAD bit first before following the readback sequence.
STATREAD can be set high again after the register read.
相關PDF資料
PDF描述
R-7215D CONV DC/DC 2A 19-28VIN 15V
VE-J14-EZ CONVERTER MOD DC/DC 48V 25W
R-7212P CONV DC/DC 2A 15-28VIN 12V
R-7212D CONV DC/DC 2A 15-28VIN 12V
VI-JVX-EZ CONVERTER MOD DC/DC 5.2V 25W
相關代理商/技術參數
參數描述
EVAL-AD5755SDZ 功能描述:BOARD EVAL FOR AD5755 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5757SDZ 功能描述:BOARD EVAL FOR AD5757 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5760SDZ 功能描述:BOARD EVAL FOR AD5760SDZ RoHS:否 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5764EB 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR QUAD, 16-BIT, HIGH ACCURACY, SERIAL INPUT, BIPOLAR VOLTAGE OUTPUT DAC 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD I.C. - Bulk
EVAL-AD5764EBZ 功能描述:BOARD EVAL FOR AD5764 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*