參數資料
型號： EVAL-AD7266EDZ
廠商： Analog Devices Inc
文件頁數： 4/29頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD7266 A/D CONV
標準包裝： 1
ADC 的數量： 2
位數： 12
采樣率（每秒）： 2M
數據接口： SPI?、QSPI?、MICROWIRE? 和 DSP
輸入范圍： 0 ~ 5 V
在以下條件下的電源（標準）： 9mW @ 3V，27mW @ 5V
工作溫度： -40°C ~ 125°C
已用 IC / 零件： AD7266
已供物品： 板
AD7266
Rev. B | Page 11 of 28
TERMINOLOGY
Differential Nonlinearity (DNL)
Differential nonlinearity is the difference between the measured
and the ideal 1 LSB change between any two adjacent codes in
the ADC.
Integral Nonlinearity (INL)
Integral nonlinearity is the maximum deviation from a straight
line passing through the endpoints of the ADC transfer
function. The endpoints of the transfer function are zero scale
with a single (1) LSB point below the first code transition, and
full scale with a 1 LSB point above the last code transition.
Offset Error
Offset error applies to straight binary output coding. It is the
deviation of the first code transition (00 . . . 000) to (00 . . . 001)
from the ideal (AGND + 1 LSB).
Offset Error Match
Offset error match is the difference in offset error across all
12 channels.
Gain Error
Gain error applies to straight binary output coding. It is the
deviation of the last code transition (111 . . . 110) to (111 . . .
111) from the ideal (VREF 1 LSB) after the offset error is
adjusted out. Gain error does not include reference error.
Gain Error Match
Gain error match is the difference in gain error across all
12 channels.
Zero Code Error
Zero code error applies when using twos complement output
coding with, for example, the 2 × VREF input range as VREF to
+VREF biased about the VREF point. It is the deviation of the
midscale transition (all 1s to all 0s) from the ideal VIN voltage
(VREF).
Zero Code Error Match
Zero code error match refers to the difference in zero code error
across all 12 channels.
Positive Gain Error
This applies when using twos complement output coding with,
for example, the 2 × VREF input range as VREF to +VREF biased
about the VREF point. It is the deviation of the last code
transition (011…110) to (011…111) from the ideal (+VREF
1 LSB) after the zero code error is adjusted out.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode after the
end of conversion. Track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within ±1/2 LSB, after the end of conversion.
Signal-to-(Noise + Distortion) Ratio
This ratio is the measured ratio of signal-to-(noise + distortion)
at the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all non-fundamental signals
up to half the sampling frequency (fS/2), excluding dc. The ratio
is dependent on the number of quantization levels in the
digitization process; the more levels, the smaller the quantization
noise. The theoretical signal-to-(noise + distortion) ratio for an
ideal N-bit converter with a sine wave input is given by
Signal-to-(Noise + Distortion) = (6.02N + 1.76) dB
Therefore, for a 12-bit converter, this is 74 dB.
Total Harmonic Distortion (THD)
Total harmonic distortion is the ratio of the rms sum of
harmonics to the fundamental. For the AD7266, it is defined as
1
2
6
2
5
2
4
2
3
2
log
20
)
(
V
dB
THD
+
=
where:
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
through the sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic, or spurious noise, is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2, excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, it is a
noise peak.
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of
crosstalk between channels. It is measured by applying a full-
scale (2 × VREF when VDD = 5 V, VREF when VDD = 3 V), 10 kHz
sine wave signal to all unselected input channels and
determining how much that signal is attenuated in the selected
channel with a 50 kHz signal (0 V to VREF). The result obtained
is the worst-case across all 12 channels for the AD7266.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities create distortion
products at sum, and difference frequencies of mfa ± nfb where
m, n = 0, 1, 2, 3, and so on. Intermodulation distortion terms
are those for which neither m nor n are equal to zero. For
example, the second-order terms include (fa + fb) and (fa fb),
while the third-order terms include (2fa + fb), (2fa fb),
(fa + 2fb), and (fa 2fb).
相關PDF資料
PDF描述
GCM22DCSH CONN EDGECARD 44POS DIP .156 SLD
0982660859 CBL 17POS 0.5MM JMPR TYPE A 3"
0210490326 CABLE JUMPER 1.25MM .076M 26POS
MAX5138EVKIT+ EVALUATION KIT FOR MAX5138
MAX5216EVKIT+ KIT EVAL FOR MAX5214/MAX5216
相關代理商/技術參數
參數描述
EVAL-AD7273CB 制造商:Analog Devices 功能描述:Evaluation Board 3 MSPS,10-/12-Bit ADCs In 8-Lead TSOT 制造商:Analog Devices 功能描述:EVAL BD 3 MSPS,10-/12-BIT ADCS IN 8-LEAD TSOT - Bulk
EVAL-AD7273CB3 制造商:AD 制造商全稱:Analog Devices 功能描述:3 MSPS,10-/12-Bit ADCs in 8-Lead TSOT
EVAL-AD7274CB 制造商:Analog Devices 功能描述:EVAL BD 3 MSPS,10-/12-BIT ADCS IN 8-LEAD TSOT - Bulk
EVAL-AD7274CB3 制造商:AD 制造商全稱:Analog Devices 功能描述:3 MSPS,10-/12-Bit ADCs in 8-Lead TSOT
EVAL-AD7274CBZ 功能描述:BOARD EVALUATION FOR AD7274 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*