- 您現在的位置：買賣IC網 > PDF目錄17060 > EVAL-AD7785EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7785 PDF資料下載
參數資料
| 型號： | EVAL-AD7785EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 15/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD7785 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 20 |
| 采樣率（每秒）： | 470 |
| 數據接口： | 串行 |
| 輸入范圍： | ±VREF |
| 工作溫度： | -40°C ~ 105°C |
| 已用 IC / 零件： | AD7785 |
| 已供物品： | 板，纜線，CD |
| 相關產品： | AD7785BRUZ-REEL-ND - IC ADC 20BIT 3CH LN LP 16-TSSOP AD7785BRUZ-ND - IC ADC 20BIT SIGMA-DELTA 16TSSOP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7785
Rev. 0 | Page 22 of 32
the AD7785 with CS being used to decode the part. Figure 3
shows the timing for a read operation from the AD7785 output
shift register, and Figure 4 shows the timing for a write opera-
tion to the input shift register. It is possible to read the same
word from the data register several times, even though the
DOUT/RDY line returns high after the first read operation.
However, care must be taken to ensure that the read operations
have been completed before the next output update occurs. In
continuous read mode, the data register can be read only once.
The serial interface can operate in 3-wire mode by tying CS low.
In this case, the SCLK, DIN, and DOUT/RDY lines are used
to communicate with the AD7785. The end of the conversion
can be monitored using the RDY bit in the status register. This
scheme is suitable for interfacing to microcontrollers. If CS is
required as a decoding signal, it can be generated from a port
pin. For microcontroller interfaces, it is recommended that
SCLK idle high between data transfers.
The AD7785 can be operated with CS being used as a frame
synchronization signal. This scheme is useful for DSP interfaces.
In this case, the first bit (MSB) is effectively clocked out by CS,
because CS would normally occur after the falling edge of SCLK
in DSPs. The SCLK can continue to run between data transfers,
provided the timing numbers are obeyed.
The serial interface can be reset by writing a series of 1s on the
DIN input. If a Logic 1 is written to the AD7785 line for at least
32 serial clock cycles, the serial interface is reset. This ensures
that the interface can be reset to a known state if the interface
gets lost due to a software error or some glitch in the system.
Reset returns the interface to the state in which it is expecting
a write to the communications register. This operation resets
the contents of all registers to their power-on values. Following
a reset, the user should allow a period of 500 μs before
addressing the serial interface.
The AD7785 can be configured to continuously convert or to
perform a single conversion. See Figure 17 through Figure 19.
Single Conversion Mode
In single conversion mode, the AD7785 is placed in shutdown
mode between conversions. When a single conversion is initi-
ated by setting MD2, MD1, MD0 to 0, 0, 1 in the mode register,
the AD7785 powers up, performs a single conversion, and then
returns to power-down mode. The on-chip oscillator requires
1 ms to power up. A conversion requires a time period of
2 × tADC. DOUT/RDY goes low to indicate the completion of a
conversion. When the data-word has been read from the data
register, DOUT/RDY goes high. If CS is low, DOUT/RDY
remains high until another conversion is initiated and com-
pleted. The data register can be read several times, if required,
even when DOUT/RDY has gone high.
Continuous Conversion Mode
This is the default power-up mode. The AD7785 continuously
converts, the RDY pin in the status register going low each time
a conversion is completed. If CS is low, the DOUT/ RDY line
also goes low when a conversion is complete. To read a conver-
sion, the user writes to the communications register indicating
that the next operation is a read of the data register. The digital
conversion is placed on the DOUT/ RDY pin as soon as SCLK
pulses are applied to the ADC. DOUT/RDY returns high when
the conversion is read. The user can read this register additional
times, if required. However, the user must ensure that the data
register is not being accessed at the completion of the next
conversion, otherwise the new conversion word is lost.
相關PDF資料 |
PDF描述 |
|---|---|
| UVZ1J332MRD | CAP ALUM 3300UF 63V 20% RADIAL |
| EVAL-AD7732EBZ | BOARD EVAL FOR AD7732 |
| VE-B2M-EY | CONVERTER MOD DC/DC 10V 50W |
| EVAL-AD7793EBZ | BOARD EVALUATION FOR AD7793 |
| RCM15DCBD-S189 | CONN EDGECARD 30POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7787CB | 制造商:Analog Devices 功能描述:DEVELOPMENT BOARD ((NS)) |
| EVAL-AD7787EB | 制造商:Analog Devices 功能描述:LOW PWR, 2CH 24BIT SIGMA-DELTA ADC - Bulk |
| EVAL-AD7788EB | 制造商:Analog Devices 功能描述:Development Tools, Low Power, 16/24Bit Sigma-Delta ADC 制造商:Analog Devices 功能描述:DEV TOOLS, LOW PWR, 16/24BIT SIGMA-DELTA ADC - Bulk |
| EVAL-AD7789EB | 制造商:Analog Devices 功能描述:DEV TOOLS, LOW PWR, 16/24BIT SIGMA-DELTA ADC - Bulk |
| EVAL-AD7790EB | 制造商:Analog Devices 功能描述:Development Tools, Low Power, 16/24Bit Sigma-Delta ADC 制造商:Analog Devices 功能描述:DEV TOOLS, LOW PWR, 16/24BIT SIGMA-DELTA ADC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。