- 您現在的位置：買賣IC網 > PDF目錄16570 > EVAL-AD7879-1EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7879-1 PDF資料下載
參數資料
| 型號： | EVAL-AD7879-1EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 20/41頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD7879-1 |
| 標準包裝： | 1 |
| 主要目的： | 接口，觸摸屏控制器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD7879-1 |
| 主要屬性： | 4 線電阻式觸控屏控制器，I²C 和 SPI 接口 |
| 次要屬性： | 圖形用戶界面，USB 接口 |
| 已供物品： | 板，線纜，CD，觸控屏 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
AD7879/AD7889
Rev. C | Page 26 of 40
CONTROL REGISTERS
DISABLE
PENIRQ
CHNL
ADD2
CHNL
ADD1
CHNL
ADD0
ADC
MODE1
ADC
MODE0
ACQ1 ACQ0 TMR7 TMR6 TMR5 TMR4 TMR3 TMR2 TMR1 TMR0
07667-
029
15
0
Figure 30. Control Register 1
CONTROL REGISTER 1
Control Register 1 (Address 0x01) contains the ADC channel
address and the ADC mode bits. It sets the acquisition time and
the timer. It also contains a bit to disable the pen interrupt.
Control Register 1 should always be the last register programmed
prior to starting conversions. Its power-on default value is 0x0000.
To change any parameter after conversion has begun, the part
must first be put into ADC Mode 00. Make the changes, and
then reprogram Control Register 1, ensuring that it is always
the last register programmed before conversions begin.
Timer (Control Register 1, Bits[7:0])
The TMR bits in Control Register 1 set the conversion interval
timer, which enables the ADC to perform a conversion sequence
at regular intervals from 550 s (00000001) up to 9.440 ms
(11111111) in increments of 35 s (see Table 18). The default
value of these bits is 00000000, which enables the ADC to
perform one conversion only.
In slave mode, the timer starts as soon as the conversion sequence
is finished. In master mode, the timer starts at the end of a conver-
sion sequence only if the screen remains touched. If the touch is
released at any stage, the timer stops. The next time that the
screen is touched, a conversion sequence begins immediately.
Table 18. Timer Selection
TMR[7:0]
Conversion Interval
00000000
Convert one time only (default)
00000001
Every 550 s
00000010
Every 585 s
00000011
Every 620 s
…
11111101
Every 9.370 ms
11111110
Every 9.405 ms
11111111
Every 9.440 ms
Acquisition Time (Control Register 1, Bits[9:8])
The ACQ bits in Control Register 1 allow the selection of acquisi-
tion times for the ADC of 2 s (default), 4 s, 8 s, or 16 s. The
user can program the ADC with an acquisition time suitable for
the type of signal being sampled. For example, signals with large
RC time constants can require longer acquisition times.
Table 19. Acquisition Time Selection
ACQ1
ACQ0
Acquisition Time
0
4 clock periods (2 s)
0
1
8 clock periods (4 s)
1
0
16 clock periods (8 s)
1
32 clock periods (16 s)
ADC Mode (Control Register 1, Bits[11:10])
The mode bits select the operating mode of the ADC. The
AD7879/AD7889 have three operating modes. These modes are
selected by writing to the mode bits in Control Register 1. If the
mode bits are set to 00, no conversion is performed.
Table 20. Mode Selection
ADC
MODE1
ADC
MODE0
Function
0
Do not convert (default)
0
1
Single-channel conversion; the device is
in slave mode
1
0
Sequence 0; the device is in slave mode
1
Sequence 1; the device is in master mode
If the mode bits are set to 01, a single conversion is performed
on the channel selected by writing to the channel bits of Control
Register 1 (Bits[14:12]). At the end of the conversion, if the TMR
bits in Control Register 1 are set to 00000000, the mode bits
revert to 00 and the ADC returns to no convert mode until a
new conversion is initiated by the host. Setting the TMR bits to
a value other than 00000000 causes the conversion to be repeated.
The AD7879/AD7889 can also be programmed to automatically
convert a sequence of selected channels. The two modes for this
type of conversion are slave mode and master mode.
For slave mode operation, the channels to be digitized are selected
by setting the corresponding bits in Control Register 3. Conversion
is initiated by writing 10 to the mode bits of Control Register 1.
The ADC then digitizes the selected channels and stores the
results in the corresponding result registers. At the end of the
conversion, if the TMR bits in Control Register 1 are set to
00000000, the mode bits revert to 00 and the ADC returns to no
convert mode until a new conversion is initiated by the host.
Setting the TMR bits to a value other than 00000000 causes the
conversion sequence to be repeated.
For master mode operation, the channels to be digitized are
written to Control Register 3. Master mode is then selected by
writing 11 to the mode bits in Control Register 1. In this mode,
the wake-up on touch feature is active; therefore, conversion
does not begin immediately. The AD7879/AD7889 wait until
the screen is touched before beginning the sequence of conver-
sions. The ADC then digitizes the selected channels, and the
results are written to the result registers. Before beginning
another sequence of conversions, the AD7879/AD7889 wait for
the screen to be touched again or for a timer event if the screen
remains touched.
相關PDF資料 |
PDF描述 |
|---|---|
| RCC28DCSN | CONN EDGECARD 56POS DIP .100 SLD |
| EEM44DSUI | CONN EDGECARD 88POS DIP .156 SLD |
| ECA28DCBN | CONN EDGECARD 56POS R/A .125 SLD |
| RCC28DCSH | CONN EDGECARD 56POS DIP .100 SLD |
| EYM18DTMS-S189 | CONN EDGECARD 36POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7879EBZ | 功能描述:BOARD EVALUATION FOR AD7879 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD7887CB | 制造商:Analog Devices 功能描述:EVAL BD FOR 2.7 V TO 5.25 V, MICROPWR, 2CH, 125 KSPS, 12-BIT - Bulk |
| EVAL-AD7887CB4 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.7 V to 5.25 V, Micropower, 2-Channel, 125 kSPS, 12-Bit ADC in 8-Lead MSOP |
| EVAL-AD7887CBZ | 功能描述:BOARD EVAL FOR AD7887 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7888CB | 制造商:Analog Devices 功能描述:EVAL KIT FOR 2.7 V TO 5.25 V, MICROPWR, 8CH, 125 KSPS, 12-BI - Bulk |
發布緊急采購，3分鐘左右您將得到回復。