- 您現在的位置：買賣IC網 > PDF目錄17111 > EVAL-ADUC7024QSZ (Analog Devices Inc)KIT DEV QUICK START ADUC7024 PDF資料下載
參數資料
| 型號： | EVAL-ADUC7024QSZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 88/104頁 |
| 文件大小： | 0K |
| 描述： | KIT DEV QUICK START ADUC7024 |
| 產品培訓模塊： | ARM7 Applications & Tools Intro to ARM7 Core & Microconverters |
| 設計資源： | ADUC7024 Dev System Schematic/Brd Outline 7024 Gerber Files |
| 標準包裝： | 1 |
| 系列： | QuickStart™ 套件 |
| 類型： | MCU |
| 適用于相關產品： | ADuC7024 |
| 所含物品： | 評估板、電源、纜線、軟件和說明文檔 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁當前第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 84 of 104
FIQ
The fast interrupt request (FIQ) is the exception signal to enter
the FIQ mode of the processor. It is provided to service data
transfer or communication channel tasks with low latency. The
FIQ interface is identical to the IRQ interface providing the
second-level interrupt (highest priority). Four 32-bit registers
are dedicated to FIQ: FIQSIG, FIQEN, FIQCLR, and FIQSTA.
Table 165. FIQSTA Register
Name
Address
Default Value
Access
FIQSTA
0xFFFF0100
0x00000000
R
Table 166. FIQSIG Register
Name
Address
Default Value
Access
FIQSIG
0xFFFF0104
0x00XXX0001
R
1
X indicates an undefined value.
Table 167. FIQEN Register
Name
Address
Default Value
Access
FIQEN
0xFFFF0108
0x00000000
R/W
Table 168. FIQCLR Register
Name
Address
Default Value
Access
FIQCLR
0xFFFF010C
0x00000000
W
Bit 31 to Bit 1 of FIQSTA are logically OR’d to create the FIQ
signal to the core and to Bit 0 of both the FIQ and IRQ registers
(FIQ source).
The logic for FIQEN and IRQEN does not allow an interrupt
source to be enabled in both IRQ and FIQ masks. A bit set to 1
in FIQEN does, as a side effect, clear the same bit in IRQEN.
Also, a bit set to 1 in IRQEN does, as a side effect, clear the
same bit in FIQEN. An interrupt source can be disabled in both
the IRQEN and FIQEN masks.
Note that to clear an already enabled FIQ source, the user must
set the appropriate bit in the FIQCLR register. Clearing an
interrupt’s FIQEN bit does not disable the interrupt.
Programmed Interrupts
Because the programmed interrupts are nonmaskable, they are
controlled by another register, SWICFG, which simultaneously
writes into the IRQSTA and IRQSIG registers and/or the
FIQSTA and FIQSIG registers. The 32-bit SWICFG register is
dedicated to software interrupts(see Table 170). This MMR
allows the control of a programmed source interrupt.
Table 169. SWICFG Register
Name
Address
Default Value
Access
SWICFG
0xFFFF0010
0x00000000
W
Table 170. SWICFG MMR Bit Descriptions
Bit
Description
31:3
Reserved.
2
Programmed interrupt (FIQ). Setting/clearing this bit
corresponds with setting/clearing Bit 1 of FIQSTA
and FIQSIG.
1
Programmed interrupt (IRQ). Setting/clearing this bit
corresponds with setting/clearing Bit 1 of IRQSTA
and IRQSIG.
0
Reserved.
Note that any interrupt signal must be active for at least the
equivalent of the interrupt latency time, which is detected by
the interrupt controller and by the user in the IRQSTA/FIQSTA
register.
TIMERS
The ADuC7019/20/21/22/24/25/26/27/28/29 have four general-
purpose timer/counters.
Timer0
Timer1
Timer2 or wake-up timer
Timer3 or watchdog timer
These four timers in their normal mode of operation can be
either free running or periodic.
In free-running mode, the counter decreases from the
maximum value until zero scale and starts again at the
minimum value. (It also increases from the minimum value
until full scale and starts again at the maximum value.)
In periodic mode, the counter decrements/increments from the
value in the load register (TxLD MMR) until zero/full scale and
starts again at the value stored in the load register.
The timer interval is calculated as follows:
If the timer is set to count down then
(
)
Clock
Source
Prescaler
TxLD
Interval
×
=
If the timer is set to count up, then
(
)
Clock
Source
Prescaler
TxLD
Fs
Interval
×
=
The value of a counter can be read at any time by accessing its
value register (TxVAL). Note that when a timer is being clocked
from a clock other than core clock, an incorrect value may be
read (due to an asynchronous clock system). In this configur-
ation, TxVAL should always be read twice. If the two readings
are different, it should be read a third time to get the correct
value.
Timers are started by writing in the control register of the
corresponding timer (TxCON).
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-ADUC845QSZ | KIT DEV FOR ADUC845 QUICK START |
| HCM15DRXS | CONN EDGECARD 30POS DIP .156 SLD |
| EVAL-ADUC832QSZ | KIT DEV FOR ADUC832 QUICK START |
| HBM15DRXS | CONN EDGECARD 30POS DIP .156 SLD |
| PCX1H270MCL1GS | CAP ALUM 27UF 50V 20% SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADUC7026QS | 制造商:Analog Devices 功能描述:MICROCONTROLLER, PRECISION ANALOG,MULTI-CHANNEL 12-BIT ADC - Bulk 制造商:Analog Devices 功能描述:EVALUATION KIT |
| EVAL-ADUC7026QSP | 制造商:Analog Devices 功能描述:Evaluation Board For Precision Analog Microcontroller, 12-Bit Analog I/O, ARM7TDMI MCU 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Bulk 制造商:Analog Devices 功能描述:EVALUATION KIT |
| EVAL-ADUC7026QSPZ | 功能描述:KIT DEV ADUC7026/7027 QUICK PLUS RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ PLUS 套件 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板，軟件，4x4 鍵盤，光學撥輪，QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA |
| EVAL-ADUC7026QS-U1 | 制造商:Analog Devices 功能描述:QUICK START DEVL SYST EVAL BOARD I.C. - Bulk |
| EVAL-ADUC7026QSZ | 功能描述:KIT DEV FOR ADUC7026/7027 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ 套件 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。