- 您現在的位置：買賣IC網 > PDF目錄1922 > FT2232D-REEL (FTDI, Future Technology Devices International Ltd)IC USB FS DUAL UART/FIFO 48-LQFP PDF資料下載
參數資料
| 型號： | FT2232D-REEL |
| 廠商： | FTDI, Future Technology Devices International Ltd |
| 文件頁數： | 15/61頁 |
| 文件大小： | 0K |
| 描述： | IC USB FS DUAL UART/FIFO 48-LQFP |
| 產品培訓模塊： | USB Introduction |
| 標準包裝： | 1 |
| 系列： | USBmadeEZ-FIFO，F(xiàn)T-X，X-Chip |
| 特點： | USB 至 UART 和（或）FIFO、SPI、I2C、JTAG |
| 通道數： | 2，DUART |
| FIFO's： | 384 字節 |
| 規程： | RS232，RS422，RS485 |
| 電源電壓： | 4.35 V ~ 5.25 V |
| 帶并行端口： | 是 |
| 帶自動流量控制功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 634 (CN2011-ZH PDF) |
| 配用： | 768-1030-ND - MOD USB HS FT2232H EVAL 813-1009-ND - MODULE USB-TO-FPGA TOOL W/MANUAL 813-1001-ND - MODULE USB ADAPTR FOR FT2232D LP 813-1000-ND - MODULE USB ADAPTER FOR FT2232D |
| 其它名稱： | 768-1010-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
Copyright 2010 Future Technology Devices International Limited
22
Document No.: FT_000173
FT2232D DUAL USB TO SERIAL UART
/FIFO IC Datasheet
Version 2.05
Clearance No.: FTDI# 127
6.1 USB Self Powered Configuration
Figure 6.2 Self Powered Configuration
Figure 6.2 illustrates the FT2232D in a typical USB self powered configuration. A USB Self
Powered device gets its power from its own POWER SUPPLY and does not draw current from the
USB bus. The basic rules for USB Self power devices are as follows –
a) A Self-Powered device should not force current down the USB bus when the USB
Host or Hub Controller is powered down.
b)A Self Powered Device can take as much current as it likes during normal operation
and USB suspend as it has its own POWER SUPPLY.
c)A Self Powered Device can be used with any USB Host and both Bus and Self
Powered USB Hubs.
The USB power descriptor option in the EEPROM should be programmed to a value of zero (self powered).
To meet requirement a) the 1.5 K pull-up resistors on USBDP is connected to RSTOUT# as per the bus-
power circuit. However, the USB Bus Power is used to control the RESET# Pin of the FT2232D device. When
the USB Host or Hub is powered up RSTOUT# will pull the 1.5K resistor on USBDP to 3.3V, thus identifying
the device as a full speed device to USB. When the USB Host or Hub power is off, RESET# will go low and
the device will be held in reset. As RESET# is low, RSTOUT# will also be low, so no current will be forced
down USBDP via the 1.5K pull-up resistor when the host or hub is powered down. Failure to do this may
cause some USB host or hub controllers to power up erratically. Note: When the FT2232D is in reset, the
I/O interface pins all go tri-state. These pins have internal 200K pull-up resistors to VCCIO, so they will
gently pull high unless driven by some external logic.
相關PDF資料 |
PDF描述 |
|---|---|
| FT2232HQ-REEL | IC USB HS DUAL UART/FIFO 64-QFN |
| FT232BL-REEL | IC USB FS SERIAL UART 32-LQFP |
| FT232HL-REEL | IC HS USB TO UART/FIFO 48LQFP |
| FT232RL-REEL | IC USB FS SERIAL UART 28-SSOP |
| FT245BL-REEL | IC USB FS PARALLEL FIFO 32-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FT2232D-TRAY | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:DUAL USB TO SERIAL UART/FIFO IC |
| FT2232H | 制造商:FTDI 制造商全稱:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART |
| FT2232H MINI MODULE | 功能描述:界面開發工具 USB Hi-Speed FT2232H Evaluation Module RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| FT2232H_10 | 制造商:FTDI 制造商全稱:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC |
| FT2232H_12 | 制造商:FTDI 制造商全稱:FTDI 功能描述:Dual High Speed USB to Multipurpose UART/FIFO IC |
發布緊急采購，3分鐘左右您將得到回復。