- 您現在的位置：買賣IC網 > PDF目錄1922 > FT2232D-REEL (FTDI, Future Technology Devices International Ltd)IC USB FS DUAL UART/FIFO 48-LQFP PDF資料下載
參數資料
| 型號： | FT2232D-REEL |
| 廠商： | FTDI, Future Technology Devices International Ltd |
| 文件頁數： | 36/61頁 |
| 文件大小： | 0K |
| 描述： | IC USB FS DUAL UART/FIFO 48-LQFP |
| 產品培訓模塊： | USB Introduction |
| 標準包裝： | 1 |
| 系列： | USBmadeEZ-FIFO，FT-X，X-Chip |
| 特點： | USB 至 UART 和（或）FIFO、SPI、I2C、JTAG |
| 通道數： | 2，DUART |
| FIFO's： | 384 字節(jié) |
| 規(guī)程： | RS232，RS422，RS485 |
| 電源電壓： | 4.35 V ~ 5.25 V |
| 帶并行端口： | 是 |
| 帶自動流量控制功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 634 (CN2011-ZH PDF) |
| 配用： | 768-1030-ND - MOD USB HS FT2232H EVAL 813-1009-ND - MODULE USB-TO-FPGA TOOL W/MANUAL 813-1001-ND - MODULE USB ADAPTR FOR FT2232D LP 813-1000-ND - MODULE USB ADAPTER FOR FT2232D |
| 其它名稱： | 768-1010-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
Copyright 2010 Future Technology Devices International Limited
41
Document No.: FT_000173
FT2232D DUAL USB TO SERIAL UART
/FIFO IC Datasheet
Version 2.05
Clearance No.: FTDI# 127
**Note 25: The Bit-Bang Mode (synchronous and asynchronous) WR# and RD# strobes are on these
pins when the main Channel mode is 245 FIFO, or Fast Opto-Isolated Serial Mode. Bit-Bang mode is not
available on Channel B when Fast Opto-Isolated Serial Mode is enabled.
**Note 26 : The Bit-Bang Mode (synchronous and asynchronous) WR# and RD# strobes are on these
pins when the main Channel mode is set to 232 UART Mode.
Enhanced Asynchronous Bit-Bang Mode
Enhanced Asynchronous Bit-Bang mode is the same as BM-style Bit-Bang mode, except that the internal
RD# and WR# strobes are now brought out of the device to allow external logic to be clocked by
accesses to the bit-bang IO bus.
On either or both channels any data written to the device in the normal manner will be self clocked onto
the data pins (those which have been configured as outputs). Each pin can be independently set as an
input or an output. The rate that the data is clocked out at is controlled by the baud rate generator.
For the data to change there has to be new data written, and the baud rate clock has to tick. If no new
data is written to the channel, the pins will hold the last value written.
To allow time for the data to be setup and held around the WR# strobe, the baud rate should be less
than 1 MegaBaud.
See the application note AN232B-01, “FT232BM/FT245BM Bit Bang Mode” for more details and a
sample application.
Enabling
Asynchronous Bit-Bang mode is enabled using Set Bit Bang Mode driver command. A hex value of 1 will
enable it, and a hex value of 0 will reset the device. See application note AN2232-02, “Bit Mode
Functions for the FT2232D” for more details and examples of this.
Synchronous Bit-Bang Mode
With Synchronous Bit-Bang mode data will only be sent out by the FT2232D if there is space in the
device for data to be read from the pins. This Synchronous Bit-Bang mode will read the data bus pins
first, before it sends out the byte that has just been transmitted. It is therefore 1 byte behind the output,
and so to read the inputs for the byte that you have just sent, another byte must be sent.
For example:-
(1) Pins start at 0xFF
Send 0x55, 0xAA
Pins go to 0x55 and then to 0xAA
Data read = 0xFF, 0x55
(2) Pins start at 0xFF
Send 0x55, 0xAA, 0xAA
(Repeat the last byte sent)
Pins go to 0x55 and then to 0xAA
Data read = 0xFF, 0x55, 0xAA
Enabling
Synchronous Bit-Bang mode is enabled using Set Bit Bang Mode driver command. A hex value of 4 will
enable it, and a hex value of 0 will reset the device. See application note AN2232-02, “Bit Mode
Functions for the FT2232D” for more details and examples.
相關PDF資料 |
PDF描述 |
|---|---|
| FT2232HQ-REEL | IC USB HS DUAL UART/FIFO 64-QFN |
| FT232BL-REEL | IC USB FS SERIAL UART 32-LQFP |
| FT232HL-REEL | IC HS USB TO UART/FIFO 48LQFP |
| FT232RL-REEL | IC USB FS SERIAL UART 28-SSOP |
| FT245BL-REEL | IC USB FS PARALLEL FIFO 32-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FT2232D-TRAY | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:DUAL USB TO SERIAL UART/FIFO IC |
| FT2232H | 制造商:FTDI 制造商全稱:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART |
| FT2232H MINI MODULE | 功能描述:界面開發(fā)工具 USB Hi-Speed FT2232H Evaluation Module RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| FT2232H_10 | 制造商:FTDI 制造商全稱:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC |
| FT2232H_12 | 制造商:FTDI 制造商全稱:FTDI 功能描述:Dual High Speed USB to Multipurpose UART/FIFO IC |
發(fā)布緊急采購，3分鐘左右您將得到回復。